Crown Verity CV-EH-1500 - Manuel (Page 2)

2
Introduction
Your infrared heater heats by way of infared radiation so your infrared heater is effective
antwhere. Because it doesn’t need to heat the ambient air (medium), it heats the object, not
the air.
Important Safety Instructions
When using electrical appliances, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, or injury to persons, etc.
Read through the operation and assembly instructions conscientiously before operating the
appliance.
Be sure to keep the manual in a safe place for future reference.
• Check if the voltage indicated on the nameplate of the appliance corresponds to the
local mains voltage before you connect the appliance.
• The power supply to the appliance should correspond to the relevant regulations of
the power supply companies and the regional construction regulations.
• Extension cords and multi-sockets may be used only if care is exercised in their use.
The marked electrical rating of the extension cord or multi-socket should have adequate
current carrying capacity and correspond to the relevant regulations of the power supply
companies and the regional construction regulations. Check if the voltage indicated on
the appliance corresponds to the marked electrical rating of the extension cord or multi-
socket before you connect the appliance.
• The appliance is not located immediately below a wall socket-outlet.
• Never install this appliance close to anything flammable, such as furniture, curtains, etc.
• In order to avoid overheating and fire hazard, do not cover or obstruct the appliance. Do
not put any of the following materials on the appliance, such as clothes, blanket, pillow,
paper etc. The minimum distance 1M (39“) between the appliance and flammable
materials must always be maintained.
• The casing and the front cover of the appliance becomes extremely hot during
operation. Pay attention that no combustible material due to Wind or other
environmental influences covers or obstructs the appliance, such as curtains, marquees,
flags, plastic foil etc. Do not touch the appliance. Caution! Risk of burn injury!
• Do not let the cord hang over edge of table or counter, or touch hot surfaces.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
• In case of improper use, there is a risk of electrical shock and/or fire hazard. Operation
of the appliance must be discontinued and remove the mains plug immediately.
• Do not try to repair the appliance by your-self. Please contact Crown Verity or a suitably
qualified electrician for maintenance.
• Remove the plug from the power outlet and wait untill the appliance is sufficiently
cooled off before cleaning.
• Do not store any burnable liquids, paint, gas tank etc. in the immediate surroundings of
the appliance.
• Do not use the appliance in flammable ambience(such as near by combustible gas or
spray cans)! Danger of explosion and fire!
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
3
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Keep out of reach of children. In order to keep children from the dangers of electrical
appliances, never leave them unsupervised with the machine. Consequently, when
selecting the location for your machine, do so in such a way that children do not have
access to the machine. Children being supervised not to play with the appliance.
• Caution! Never leave the appliance unsupervised when in use. Do not use the
appliance with a programmer, timer or any other device that switches the appliance on
automatically.
• To avoid hazards, do not use the appliance with an external voltage regulator(such as
dimmer, speed controller etc.)
• The appliance must only be mounted by an authorised specialist, paying attention to the
relevant regulations of the power supply companies and the regional construction
regulations.
Installation
For additional protection the installation of a residual current device (RCD) is advisable.
1. Remove all package material (including anti-vibration object of the lamp) and
check the appliance, supply cord and the plug for signs of damage.
2. Pay attention to the mounting place and all mounting material(dowels, screws).
Ensure they are suitable and stable enough for mounting and lastingly holding of
the appliance.
3. Before mounting, the minimum safe mounting distances and tilt angles shown in
the figures must be strictly followed.
The distance between the bottom edge of the appliance and the floor must be at least
1.8 M.
There must be a distance of at least 0.5 M (20“) between the appliance and the
cellings, roofs or other covers.
There must be a distance of at least 1.5 M (59“) at each side between the appliance
and walls or the like. See figure 3.
The max. degree to mounting surface is 145°and the min. degree is 45°. See figure 4.
The infrared heater could also be swung from left to right. The max. swing degree is
90°
4. Pay attention that, the installation of the appliance does not add excessive wind
load to the mounting surface.
5. Fix the mounting bracket on the wall first. Ensure that the place to be installed is
secure and firm. Or consider the optional stand.
6. Adjust the desired angle of radiation and set all screws.
Check the screws regularly to avoid oscillation due to wind .
7. Plug in the power source. Then observe, whether during the first 10-15 minutes
the appliance works trouble-free.