Dock Edge + Solar Cleat Lite - Manuel

IMPORTANT - PLEASE READ BEFORE ASSEMBLY
THIS PRODUCT IS NOT INTENDED AS A MOORING BEACON AND IS
NOT TO BE USED FOR NAVIGATION PURPOSES
Securing the Solar Cleat Lite to the dock or other surface
1- Choose a desirable mounting location for the Solar Cleat Lite with good sun exposure.
2- Place the metal mounting base in the desired position on the mounting surface.
Ensure that the mounting base is no less than 1 1/4” back from any edge to allow
clearance for the post skirt/ trim ring. (A)
3- Ensure that the cleat mounting side of the base (4 holes on the vertical face) is towards the side of the dock that you wish have the cleat
accessible from.
4- Mark the bolt hole locations through the mounting base and drill pilot or through holes into the mounting/ dock surface. Using lag bolts of
adequate size or through bolts with lock nuts and washers, secure the mounting base to the surface. (A)
Note: Concrete mounting surfaces will require concrete screw inserts.
5- Slide the 4” PVC post over the mounting base making sure the cleat holes and the holes in the post are aligned.(A)
6- Slide the post skirt/ trim ring over the post to the bottom where two locking tabs should engage in the preformed holes of the PVC post. (B)
7- Align the tie-up cleat with the holes in the Post and insert the tapered screws through the cleat , PVC post and mounting base. Using locking
nuts on the inside of the post, secure the cleat to the post making sure each has been tightened sufficiently. (C)
Attaching the solar light fixture to the post
1- Invert the solar light fixture to view inside the lens area and remove battery contact strip(s). To ensure maximum battery contact for charging
and illumination, the battery holders in your Solar Cleat Lite are constructed in such a manner as to ensure a tight fit at all times.
If the batteries are not already installed in your Solar Cleat Lite or should they require replacement, it may be necessary for you to twist and/ or
turn the batteries slightly as they are removed or inserted and also once they are in place to ensure proper contact.
2- Align the Solar Cleat Lite lens to the PVC post opening, making sure to align the predrilled screw holes on opposite sides of the post. Secure
the lens to the post with self-tapping screws. Do not over-tighten the screws or damage to the lens may occur. (D)
• Make certain the batteries are charged. Expose the solar panel on the assembly to at least one full day of bright sun.
Troubleshooting & Battery Installation/ Replacement
Due to the simplicity of this product, very little can go wrong. However, if your light does not appear to be working properly please try the following.
• It is not necessary to remove the solar mounting screws on the PVC pillar. Looking under the edge of the solar light cap, gently pry upward on one of
the two sides that has two notches on the underside. To reinstall, position the tabs of the cap with the holes in the lens & gently press onto solar lens (E).
• Make certain that the batteries are inserted properly.....see (+) and (-) markings
• Move the batteries back and forth slightly or rotate them while they are in thier compartments to ensure proper contact.
WARRANTY
Solar Light Assembly: If within two (2) years from the date of purchase, this product fails due to a defect in material or workmanship contact the
manufacturer at: (877) 703-3412 (warranty terms and conditions found on manufacturers solar light assembly instructions)
Cleat, Post & Mounting Bracket: If within two (2) years from the date of purchase, this product fails due to a defect in material or workmanship
Dock Edge+ Inc. will repair or replace it, at its sole option, free of charge. This warranty applies only to the original purchaser and is not transferable.
DOCKEDGE+ INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLU-
SION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITYAND
THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMIT-
ED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW
LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
The warranty does not apply to: (a) damage caused by accident, abuse, in handling, dropping; (b) acts of God; (c) units which have been subject to
unauthorized repair, opened, taken apart or otherwise modified; (d) units not used in accordance with directions; (e) damages exceeding the cost of
the product; (f) the finish on any portion of the product, such as surface scratches and/ or weathering, as this is considered normal wear and tear.
Some states do not allow limitation of damages so the foregoing limitation may not apply to you. This warranty gives you specific legal rights and you
may also have other rights, which vary from state to state.
Warranty service is available by mailing postage prepaid to the authorized service station listed below. Please be sure to wrap the product securely
when mailing to avoid shipping damage. This warranty is made by:
DockEdge+ Inc., 35 Armthorpe Rd., Brampton, ON, L6T 5M4 www.dockedge.com 1-800-295-3625
1.25”
Locking Tab
Pry
Upward to
Remove
Preformed Locking Tab Hole
A B C D E
1.2
5”
Mark & Drill
4 Locations
Align Cleat
Holes
To remove solar light assembly
for inspection or battery replacement