Indesit I6GGC2G(X)-FR - Manuel (Page 22)

22
GB
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring showing
the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an anticlockwise
direction so that it is pointing to the maximum flame
setting .
3. Adjust the intensity of the flame to the desired level by
turning the BURNER knob in an anticlockwise direction.
This may be the minimum setting , the maximum setting

or any position in between the two.
If the appliance is fitted with an electronic lighting
device* (see fi gure), press the ignition button, marked
with the symbol

, then hold
the BURNER knob down and turn
it in an anticlockwise direction,
towards the maximum flame
setting, until the burner is lit.The
burner may be extinguished
when the knob is released. If
this occurs, repeat the operation,
holding the knob down for a longer period of time.
! If the flame is accidentally extinguished, switch off the
burner and wait for at least 1 minute before attempting
to relight it.
If the appliance is equipped with a flame failure
safety device*, press and hold the BURNER knob for
approximately 2-3 seconds to keep the flame alight and
to activate the device.
To switch the burner off, turn the knob until it reaches the
stop position
•.
Practical advice on using the burners
For the burners to work in the most efficient way possible
and to save on the amount of gas consumed, it is
recommended that only pans that have a lid and a flat
base are used. They should also be suited to the size of
the burner.
Flame adjustment according to levels
The burner flame intensity can be adjusted with the knob
according to 6 power levels, from maximum to minimum
with 4 intermediate positions:
Start-up and use
a click will indicate the change from one level to another
when turning the knob. The system guarantees a more
precise adjustment, allows to replicate the flame intensity
and to identify easily the preferred level for different
cooking operations.
To identify the type of burner, please refer to the diagrams
contained in the “Burner and nozzle specifications”.
Burner Cookware diameter (cm)
Rapid (R) 24 - 26
Semi-Rapid (S) 16 - 20
Auxilliary (A) 10 - 14
! On the models supplied with a reducer shelf, remember
that this should be used only for the auxiliary burner when
you use casserole dishes with a diameter under 12 cm.
WARNING! The glass lid can break in if it
is heated up. Turn off all the burners and
the electric plates before closing the lid.
*Applies to the models with glass cover
only.
Using the oven
! The first time you use your appliance, heat the empty
oven with its door closed at its maximum temperature
for at least half an hour. Ensure that the room is well
ventilated before switching the oven off and opening the
oven door. The appliance may emit a slightly unpleasant
odour caused by protective substances used during the
manufacturing process burning away.
! Never put objects directly on the bottom of the oven; this
will avoid the enamel coating being damaged.
Lighting the oven
To light the oven burner, bring
a flame or gas lighter close to
opening F (see fi gure) and press
the OVEN control knob while
turning it in an anticlockwise
direction until it reaches the MAX
position.
If the appliance is fitted with an electronic lighting device*
(see figure), simply press the OVEN control knob and turn
it in an anticlockwise direction, towards the MAX position,
until the burner is lit. If, after 15 seconds, the burner is
still not alight, release the knob, open the oven door and
wait for at least 1 minute before trying to light it again. If
*
Only available in certain models.
F