Listening through a receiver, Check points before requesting service – Samsung PS50A467P1M Manuel d'utilisation

Page 47

Advertising
background image

English - 47

Listening through a Receiver

You can listen to sound through a receiver instead of the TV speaker.
1
Press

the

TOOLS button.

Press the ▲ or ▼ button to select Receiver, then press the ENTER
button.

2

Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.

3 Press

the

EXIT button to exit.

®

output from the TV’s Optical jack. When the TV is displaying a DTV(air)
signal, the TV will send out 5.1 channel sound to the Home theater
receiver. When the source is a digital component such as a DVD and is
connected to the TV via HDMI, only 2
channel sound will be heard from the Home Theater receiver.

®

®

Out jack of the TV.

®

power failure), the TV Speaker may be set to Off when you turn the TV on again.

Check Points before Requesting Service

Symptom

Solution

Anynet+ does not work.

■ Check if the device is an Anynet+ device. The Anynet+ system supports

Anynet+ devices only.

■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
■ Check whether

Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI cable, please make sure to search

devices again or restart your TV.

■ Check if the Anynet+ Function of Anynet+ device is set on.

I want to start Anynet+.

■ Check if the Anynet+ device is properly connected to the TV and check if the

Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.

■ Press the TV button on the TV remote control to switch to TV. Then press the

TOOLS button to show the Anynet+ menu and select a menu you want.

I want to exit Anynet+.

■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a device

other than Anynet+ devices.

■ Press any of CH, CH LIST, and PRE-CH to change to the

TV mode. (Note that the channel button operates only when a tuner-
embedded Anynet+ device is not connected.)

The message Connecting to
Anynet+ device… appears on the
screen.

■ You cannot use the remote control when you are configuring Anynet+ or

switching to a view mode.

■ Use the remote control when the Anynet+ setting or switching to view mode is

complete.

The Anynet+ device does not play.

■ You cannot use the play function when Plug & Play is in progress.

The connected device is not
displayed.

■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether

Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

■ Search

Anynet+ devices again.

■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI

cables may not support Anynet+ functions.

The TV programme cannot be
recorded.

■ Check whether the antenna jack on the recording device is properly

connected.

The TV sound is not output
through the receiver.

■ Connect the optical cable between TV and the receiver.

Tools

Move

Enter

View TV

Device List

Recording : DVD

DVD Menu

DVD Menu

Picture Mode

: Dynamic

Sound Mode

: Standard

Sleep Timer

: Off

Exit

w ™–—ŒOw[\WPiu]_TWX\[^hU•‹‰GGG[^

YWW_TW\TX\GGG㝘䟸GZaYXaWW

Advertising
Ce manuel est liée aux produits suivants: