Bosch SGE63E06UC - Manuel (Page 22)

Problem Cause Acion
Dishwasher not
illing with water 1. Restricion in the water supply system.
2. Previous wash cycle was not completed.
3. Delay-start is acive. 1. Ensure that the water supply valve (typically located under kitch-
en sink) is open and check that the water supply line has no kinks
and clogs.
2. Refer to the “Canceling or changing the cycle” secion of this
manual.
3. Cancel the delay-start or wait unil delay-start ime completes
(imes out). Refer to the “Delay Start” secion of this manual.
Water Leaks 1. Suds
2. Door seal could be pulled away from track.
3. Condensaion vent is blocked.
4. Improper installaion. 1. Wrong type of detergent results in suds and leaks. Use only
dishwasher detergents. If suds sill persist, then add one ta-
blespoon of vegetable oil at the botom of the dishwasher
and run the desired cycle.
2. Ensure that door seal is in the track.
3. Ensure that condensaion vent is not blocked. Refer to “Load-
ing Extra Tall Items” in the Preparing and Loading the Dish-
washer secion of this manual.
4. Have proper installaion veriied by qualiied personnel (wa-
ter supply, drain system, leveling, plumbing).
Tub stains 1. Stains on the dishwasher interior are due to hard-
ness of water.
2. Silverware in contact with tub.
1. Concentrated Lemon juice can reduce the build up of hard
water stains. Run a normal cycle unil it lushes and interrupt
the cycle and then place an 8 oz. cup of the concentrated
lemon soluion on the top rack and inish the cycle. This can
be done periodically to avoid build up.
2. Ensure that the silverware does not make contact with the
tub while running a cycle.
Streaks on glass-
ware or residue
on the dishes Incorrect rinse agent seing. Depending on the hardness of water, adjust the rinse agent dis-
penser. Refer to “Adding Detergent and Rinse Agent” secion in this
manual for adjustment.
Fascia panel
discolored or
marked Abrasive cleaner used. Use mild detergents with sot damp cloth.
Noise during
wash cycle The dishes may not be arranged properly. Water circulaion sound is normal, but if you suspect items are
banging into each other or into the spray arms, refer to the “Pre-
paring and Loading” secion of this manual for opimal arrange-
ment.
Detergent dis-
penser cover will
not shut 1. Improper operaion of detergent cover.
2. Previous cycle has not been inished, reset, or cycle
was interrupted.
1. Refer to “Adding Detergent and Rinse Aid” secion of this man-
ual for instrucions on opening and closing the dispenser.
2. Refer to the “Canceling or changing the cycle” secion of this
manual.
Unable to select
desired cycle Previous cycle has not inished or another cycle has
already started. Refer to the “Canceling or changing the cycle” secion of this
manual.
Error Codes If fault code (E01 to E30) is indicated on the digital display 3 , irst disconnect the appliance from the power supply. You can
recify certain faults yourself (see following fault descripion), for all other faults please contact customer service and state the
indicated fault E:XX.
Water is let in
the appliance
at the end of the
programme
1. (E24) Waste water hose is blocked or kinked.
2. (E25) Waste water pump blocked, cover on the
waste water pump is not locked in posiion
3. Filters blocked.
4. The programme has not yet ended.
1. See Care and Maintenance.
2. Wait unil programme ends (digital display indicates 0:00) or
implement the ”Reset”funcion.
21