STI 1210E - Manuel

Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected] • Web: www.sti-europe.com
INSTALLATION OF STI-1210E SPEAKER HORN/STROBE DAMAGE STOPPER®
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. To minimize strobe light loss, regardless of the type
of horn/strobe appliance used, the clear section
(not the section containing the cutout slots) must be
centered over the strobe light lens. Failure to follow
these instruction may lead to light loss transmission.
2. Damage Stopper must be installed to comply with
applicable NEC, NFPA and local codes.
3. In applications where wash downs, rainfall or
condensation occur, it is recommended that a drain
or weep hole be provided. Refer to weep hole
installation diagram.
4. Damage Stopper may be installed outdoors when
appliance carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1210EIS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove abrasive dust and dirt. Wash with
soap or mild detergent, using a soft cloth (do not scrub). Rinse
once more then dry with a soft cloth or chamois. To remove
grease or wet paint, rub gently with a cloth wetted with
naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Using enclosure assembly as a template, place against mounting surface at proper location according to NFPA 72.
2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 in. (25mm) deep.
3. Insert the (4) anchors into the wall.
4. Mount frame assembly to wall with screws.
5. Install electrical fittings as needed.
6. Install horn/strobe appliance (except for retrofit applications).
7. Install cover with clips and screws.
8. Test appliance according to appliance manufacturer’s instructions.
INTERNAL DIMENSIONS
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
HEIGHT
8.5 in.(216mm)
DEPTH
4 in.(102mm)
WIDTH
6.5 in.(165mm)
PRODUCT DIMENSIONS
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
!
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297E FRAME ASSY.
CLEAR
SECTION
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
HEIGHT
8.5 in.(216mm)
DEPTH
4 in.(102mm)
WIDTH
6.5 in.(165mm)
PRODUCT DIMENSIONS
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
!
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297E FRAME ASSY.
CLEAR
SECTION
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
HEIGHT
8.5 in.(216mm)
DEPTH
4 in.(102mm)
WIDTH
6.5 in.(165mm)
PRODUCT DIMENSIONS
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
!
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297E FRAME ASSY.
CLEAR
SECTION
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
629764 CLAMP
(4) PROVIDED
19013 SCREW
#10 x 1 1/2 in.
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
APPROX
CENTER LINE
OF UNDERSIDE OF
COVER
1 in.(25mm)
HEIGHT
8.5 in.(216mm)
DEPTH
4 in.(102mm)
WIDTH
6.5 in.(165mm)
PRODUCT DIMENSIONS
1
2
INSTALL CLAMP IN 2nd. NOTCH AS SHOWN
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-121
ENVIRO KIT
EXISTING
FLUSH MOUNT
HORN/STROBE
APPLIANCE
!
LOCATED IN THIS AREA
DRILL A 1/4 in.(6.3mm) DIA. HOLE
19047 #8-32 x 3/8 in.
SOCKET HEAD CAP SCREW
(4) PROVIDED
06297E FRAME ASSY.
CLEAR
SECTION
01210 COVER ONLY
01210 COUVERCLE SEULEMENT
WEEP HOLE INSTALLATION
REMARQUES SUR L’INSTALLATION
1. Afin de minimiser la perte de lumière stroboscopique, quel que soit le type d’alarme sonore/de stroboscope utilisé, la
section dégagée (et NON la section contenant les fentes de découpe), doit être centrée sur l’objectif stroboscopique. Le fait
d’omettre ces instructions risque d’entraîner la perte de diffusion de la lumière.
2. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes NEC, NFPA applicables et les codes locaux.
3. Dans les applications où des jets d’eau, des précipitations ou de la condensation se produisent, il est recommandé de
prévoir un trou de vidange ou une barbacane. Reportez-vous à schéma d’installation d’une barbacane.
4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est homologué pour utilisation à l’extérieur.