Dqs timing configuration – Asus M4N72-E Manuel d'utilisation
Page 59
Chapitre 2 : Le BIOS
2-15
DCT0:CS/ODT drive strength [Auto]
Options de configuration : [Auto] [1x] [1.25x] [1.5x] [2x]
[Auto] [1x] [1.25x] [1.5x] [2x]
DCT0:Address/Command drive str [Auto]
Options de configuration : [Auto] [1x] [1.25x] [1.5x] [2x]
[Auto] [1x] [1.25x] [1.5x] [2x]
DCT0:MEMCLK drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT0:Data drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT0:DQS drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT0:Processor on-die terminat [Auto]
Options de configuration : [Auto] [300 ohms +/- 20�] [150 ohms +/- 20�] [75 ohms +/- 20�]
[Auto] [300 ohms +/- 20�] [150 ohms +/- 20�] [75 ohms +/- 20�]
Les sous-éléments suivants n’apparaissent que si DCT0/DCT1 Strength Config. est réglé
sur [DCT 1] ou [Both].
DCT1:CKE drive strength [Auto]
Options de configuration : [Auto] [1x] [1.25x] [1.5x] [2x]
[Auto] [1x] [1.25x] [1.5x] [2x]
DCT1:CS/ODT drive strength [Auto]
Options de configuration : [Auto] [1x] [1.25x] [1.5x] [2x]
[Auto] [1x] [1.25x] [1.5x] [2x]
DCT1:Address/Command drive strength. [Auto]
Options de configuration : [Auto] [1x] [1.25x] [1.5x] [2x]
[Auto] [1x] [1.25x] [1.5x] [2x]
DCT1:MEMCLK drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT1:Data drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT1:DQS drive strength [Auto]
Options de configuration : [Auto] [0.75x] [1x] [1.25x] [1.5x]
[Auto] [0.75x] [1x] [1.25x] [1.5x]
DCT1:Processor on-die termina [Auto]
Options de configuration : [Auto] [300 ohms +/- 20�] [150 ohms +/- 20�] [75 ohms +/- 20�]
[Auto] [300 ohms +/- 20�] [150 ohms +/- 20�] [75 ohms +/- 20�]
DQS Timing Configuration
Cet élément apparaît uniquement lorsque vous réglez l’élément AI Overclocking sur
[Manual]. Il vous permet d’ajuster les valeurs DQS.
Les sous-éléments suivants suivants apparaissent uniquement lorsque vous réglez
l’élément DQS Timing Configuration sur [DCT 0], [DCT 1] ou [Both].
CKE Setup Time [Auto]
Options de configuration :
[Auto] [1/2 CLK] [1 CLK]
CS/ODT Setup Time [Auto]
Options de configuration :
[Auto] [1/2 CLK] [1 CLK]