Whirlpool duet GHW9200LQ0 - Manuel (Page 4)

4
INSTALLATION
REQUIREMENTS
Tools and Parts
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■ Pliers (that open to 1 ⁹⁄₁₆ in. [39.5 mm])
■ Flashlight (optional)
Tools needed for installation
■ Open end wrench ⁵⁄₈ in. (17 mm) and ½ in. (13 mm)
■ Level
■ Wood block (2" x 4")
■ Ruler or measuring tape
Parts supplied:
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the "Assistance or Service" section.
Optional Pedestal
A pedestal may be purchased separately for this washer. This
pedestal will add about 13 in. (33 cm) to the height of your unit for
a total vertical height of approximately 51 in. (130 cm).
Optional Pedestal
To order, call the dealer from whom you purchased your washer
or refer to the “Assistance or Service” section of this manual. Ask
for model number LAB2700LQ.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. (See “Drain
System.”)
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
■ A water heater set to deliver 120°F (49°C) water to the washer.
■ A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
(See “Electrical Requirements.”)
■ Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
■ A level floor with a maximum slope of 1 in. (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
■ A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in
low temperatures.
Installation clearances
■ The location must be large enough to allow the washer door
to be fully opened.
■ Additional spacing should be considered for ease of
installation and servicing.
■ Additional clearances might be required for wall, door, and
floor moldings.
■ Additional spacing of 1 in. (2.5 cm) on all sides of the washer
is recommended to reduce noise transfer.
■ Companion appliance spacing should also be considered.
Beaded strap Transport bolt hole plug (4)
If You Have You Will Need to Buy
Laundry tub or
standpipe taller
than 96 in. (2.4 m) Sump pump system (if not already
available)
Overhead sewer Standard 20 gal. (76 L), 30 in. (76.2 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285834;
additional drain hose Part Number
8318155; and connector kit, Part
Number 285835
Drain hose too
short Drain hose extension kit, Part Number
285863
Water faucets
beyond reach of
fill hoses 2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008