Nuvo NV-I8GMS - Manuel (Page 6)

4
R
OUTPUT POWER OUTPUT POWER
20W/6OHM X2 20W/6OHM X2
SYS ON
EXT. MUTE
L
R
L
R
L
R
VARIABLE
OUTPUT
FIXED
OUTPUT
SUM1
3033118
C US
CONFORMS TO
UL STD.6500 CERTIFIED TO
CAN/CSA STD.E60065
NuVo Technologies Cincinnati Ohio USA
FUSE:T5 A 120V 60Hz 500W
MODEL NV-I8DM SIX SOURCE EIGHT ZONE AUDIO DISTRIBUTION SYSTEM
www.nuvotechnologies.com
OUTPUT POWER OUTPUT POWER OUTPUT POWER
20W/6OHM X2 20W/6OHM X2 20W/6OHM X2 TIP=L
RING=R
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VARIABLE
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R
VARIABLE
OUTPUT
VARIABLE
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
TIP=L
RING=R TIP=L
RING=R
1 2 3 4 5 6
1 2 3 4 5 6
2 3 4 1 2 3
RS-232
CONNECT TO
NV-I8X
USE NV-SLC1
CABLE
CONNECT TO
NV-I8X
USE NV-SLC1
CABLE
CONNECT TO
NV-I8EZP1
USE NV-NC1
CABLE
USE CNLY WITH 250V FUSE
4 5 6 SUM2 5 6 7 8
OUTPUT POWER
20W/6OHM X2
ZONE 6 ZONE 6 ZONE 7&8
SYSTEM ZONE TRIGGER OUTPUTS SOURCE LINK SOURCE INPUTS
ZONE 1
NETWORK EMITTER OUTPUTS DIGITAL LINK
ZONE 3 ZONE 4 ZONE 5 ZONE 2 PROGRAM
6 4 5
3 1 2
SOURCE STATUS INPUTS
1 2 3 4 5
6
7
8
9 10 11 12 14 13
1
Grand Concerto Back Panel
1. Variable Lineouts: These preamp lineouts are used for sending an audio signal to an external power amplifier. This is useful
for large areas that require additional pairs of speakers. Use the variable output when you want the additional amplifier to be
controlled by the zone's Display Pad.
2. Fixed Lineouts: These preamp lineouts are used for sending an audio signal to an external power amplifier when additional
speakers are needed. This output is constant, so an amplifier connected to it will not change volume with that zone's Display
Pad.
3. Source Inputs: The Grand Concerto will accept up to six audio sources. These are connected to the Grand Concerto amplifier
with standard stereo RCA cables.
4. Speaker Output: Six of the Grand Concerto's eight zones are amplified. These outputs accept 16-gage, two-conductor speaker
wire and provide 40 watts per channel of power.
5. Source Link: This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. The
source link cable is supplied with the Expander System.
6. Source Status Inputs: These optional inputs can be used to monitor source power status. This is useful when using a macro
string of commands to prevent turning off a piece of equipment that is already on and vice versa.
7. Zone Trigger Outputs: These 12-volt outputs can be used to trigger an external device, such as an auxiliary power amplifier, for
use in a specific zone.
8. IR Emitter Outputs: IR signals received from the keypads are passed through the IR outputs to the source equipment using the
supplied IR emitters. Outputs 1-6 are routed to the corresponding sources, and the SUM outputs 1 and 2 are common and will
pass all IR signals.
9. SYS. ON: This is a constant 12-volt output for turning on external equipment.
10. EXT. MUTE: This input is designed to temporarily mute any audio playing through the system when the doorbell or phone
rings. This works in conjunction with the NuVo NV-MI1 mute interface accessory. It also acts as a mute for whole-house paging
through a phone system when set for this function in the Configurator software.
11. Network Input: This RJ45 connection is the input for all zone information coming from the Grand Concerto Control Pads. The
connection is made using the Network Cable supplied with the package.
12. Digital Link: This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. The
Digital Link cable is supplied with the Expander System.
13. RS232: The bidirectional RS232 is a serial communication port that allows the Grand Concerto System to be controlled by an
external home automation device.
14. AC: A detachable power cord connects the system to an external AC power supply.