Jacuzzi AIR BATHS LUXURY SERIES - Manuel (Page 5)

Jacuzzi © Whirlpool Bath: Installation and Operation Page  BE76000F • December 2007
ENGLISH
Blower
2”
(51 mm)
W L
H 4”
(102 mm)
SPECIFICAtIONS
A
B
Drain/Overflow
SIDE VIEW END VIEW
Allusion
Bellavista 5.5 and 6
SIDE VIEW END VIEW
Blower 2”
(51 mm)
W L
H
MODEL DIMENSIONS DRAIN/OVERFLOW CUtOUt tOtAL WEIght/
FLOOR LOADINg
OPERAtINg
gALLONS
PRODUCt
WEIght
SKIRt AND
MOUNtINg
ALLUSION 6636
800W
66" (1829 mm) L
36" ( 914 mm) W
26" ( 660 mm) H
17-3/8" (441 mm) A
11-15/16" (210 mm) B
Template Provided
P/N BY20000
868 lb (395 kg)/
53 lb/ft 2 (259 kg/m 2 )
58 U.S. gal
(220 liters)
135 lb
(61 kg)
Not
available
ALLuSIoN 7236
800W
72" (1829 mm) L
36" ( 914 mm) W
26" ( 660 mm) H
17-3/8" (441 mm) A
11-15/16" (210 mm) B
Template Provided
P/N BY20000
945 lb (430 kg)/
53 lb/ft 2 (259 kg/m 2 )
66 U.S. gal
(250 liters)
145 lb
(66 kg)
Not
available
ALLuSIoN 7242
800W
72" (1829 mm) L
42" (1067 mm) W
26" ( 660 mm) H
17-3/8" (441 mm) A
11-15/16" (210 mm) B
Template Provided
P/N BY20000
1170 lb (532 kg)/
56 lb/ft 2 (273 kg/m 2 )
73-94 U.S. gal
(277 to 356 liters)
155 lb
(70 kg)
Not
available
BELLAVISTA 5.5'
800W
66" (1676 mm) L
42" (1067 mm) W
26" ( 660 mm) H
20" (508 mm) A
11-3/4" (298 mm) B
Template Provided
P/N P187000
1078 lb (490 kg)/
56 lb/ft 2 (273 kg/m 2 )
85 U.S. gal
(322 liters)
120 lb
(56 kg)
Not
available
BELLAVISTA 6'
800W
72" (1829 mm) L
42" (1067 mm) W
26" ( 660 mm) H
20" (508 mm) A
11-3/4" (298 mm) B
Template Provided
P/N P187000
1180 lb (535 kg)/
56.2 lb/ft 2 (274.4 kg/m 2 )
90 U.S. gal
(341 liters)
130 lb
(59 kg)
Not
available
NOtE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6.4 mm).
ELECTRICAL SERVICE REQUIREMENTS: 115 VAC, 15 AMP, 60 Hz.
Requires dedicated separate GFCI protected circuit.
Gallons given are in U.S. gallons.
IMPORtANt: Read complete instructions before beginning
installation.
Each bath arrives ready for installation, completely equipped
with blower motor and plumbing necessary for operation. A
drain/overflow kit is included for installation on the bath.
Remove the bath from the carton. Retain the shipping carton
until satisfactory inspection of the product has been made. Do
not lift the bath by the plumbing at any time; handle by the
shell only.
Immediately upon receipt, inspect the shell before installing.
Should inspection reveal any damage or defect in the finish, do
not install the bath. Damage or defect to the finish claimed after
the bath is installed is excluded from the warranty. Jacuzzi ©
Whirlpool Bath’s responsibility for shipping damage ceases upon
delivery of the products in good order to the carrier.
RECtANgULAR BAthS
Refer any claims for damage to the carrier. For definitions
of warranty coverage and limitations, refer to the published
warranty information packed with the product. All bath units are
factory tested for proper operation and watertight connections
prior to shipping.
NOtE: Prior to installation, the bath must be filled with water
and operated to check for leaks that may have resulted from
shipping damage or mishandling. Jacuzzi © Whirlpool Bath is
not responsible for any defect that could have been discovered,
repaired, or avoided by following this inspection and testing
procedure.