Memorex mph 6955 - Manuel (Page 8)

Setting Up Your Phone
Raising the Antenna
Before using your phone, be sure to raise its antenna to the
vertical position.
Adjusting Ringer/Volume Controls
▼ Ringer Tone and Volume
1. While the phone is not in use, press
VOLUME
.
2. The phone has two ringer tones, each with two volume levels.
Press
VOLUME
again until you hear the ringer tone and
volume level you want.
▼
Setting the Handset Earpiece Volume
1. While you are on a call, press
VOLUME
.
2. The phone has three receiver volume levels, Normal, High and
Loud. Press
VOLUME
again until you hear the volume level
you want. When you hang up, the phone keeps the last
volume setting selected.
Using Your Phone
Making and Receiving Calls
Storing a Number in Memory
Your MPH 6955 phone has 10 memory locations for storing
important telephone numbers.
1. Remove the handset from
the base and press
MEM
.
The
TALK
LED flashes and
you hear a beep.
2. Enter the phone number
you want to store (up to
16 digits).
3. Press
MEM
and enter a number (0-9) on the keypad for
the memory location you want to use.
You hear a long beep and the
TALK
LED goes out indicating
the number has been stored successfully.
If you select any keys other than 0-9, the handset will beep
rapidly and no number will be stored.
8
Setting Up Your Phone
Raising the Antenna
Before using your phone, be sure to raise its antenna to the
vertical position.
Adjusting Ringer/Volume Controls
▼ Ringer Tone and Volume
1. While the phone is not in use, press
VOLUME
.
2. The phone has two ringer tones, each with two volume levels.
Press
VOLUME
again until you hear the ringer tone and
volume level you want.
▼
Setting the Handset Earpiece Volume
1. While you are on a call, press
VOLUME
.
2. The phone has three receiver volume levels, Normal, High and
Loud. Press
VOLUME
again until you hear the volume level
you want. When you hang up, the phone keeps the last
volume setting selected.
Using Your Phone
Making and Receiving Calls
Storing a Number in Memory
Your MPH 6955 phone has 10 memory locations for storing
important telephone numbers.
1. Remove the handset from
the base and press
MEM
.
The
TALK
LED flashes and
you hear a beep.
2. Enter the phone number
you want to store (up to
16 digits).
3. Press
MEM
and enter a number (0-9) on the keypad for
the memory location you want to use.
You hear a long beep and the
TALK
LED goes out indicating
the number has been stored successfully.
If you select any keys other than 0-9, the handset will beep
rapidly and no number will be stored.
Handset on Base Handset off Base
Answer call
When the phone rings, remove the handset from the base.
(AutoTalk)
Press any key.
Make call
1. Remove the handset from the base and press
TALK
.
2. The
TALK
LED lights.
3. Listen for the dial tone.
4. Dial the number.
1. Pick up the handset and press
TALK.
2. The
TALK
LED lights.
3. Listen for the dial tone.
4. Dial the number.
Hang up Return handset to the base. (AutoStandby) Press
TALK.
Redial
1. Remove the handset from the base and press
TALK.
2. Listen for the dial tone.
3. Press
REDIAL
to dial the number.
1. Pick up the handset and press
TALK .
2. Listen for the dial tone.
3. Press
REDIAL
to dial the number.
NOTE
You have 20 seconds after pressing
MEM
to enter the number you wish to store.
Otherwise, an error tone will sound.
NOTE
You cannot store numbers in
M1
,
M2
, or
M3
. Refer to “One-Touch Dialing.”
H:...MPH 6955 Map OM.vp
Mon Jun 28 16:00:18 1999
Color profile: Disabled
Composite Default screen