V operation and settings, Initial set up, Watching a tv program – FUNAI CMWC13D6 Manuel d'utilisation

Page 9

Advertising
background image

VOLUME

20

C C C C C C

C C C C C C C C C C

AUX

1

Press [STANDBY-ONy] to turn on the unit.

NOTES:

If the TV screen shows snow

noise and there is no operation
for more than 10 seconds,

"HELPFUL HINTS" appears.

• Make sure if the antenna or cable is connected

properly. (Refer to "ANTENNA/CABLE CONNEC-
TIONS" on page 6.)

• Set the "AUTO CH PROGRAMMING" in the

CHANNEL SET UP. (Refer to "CHANNEL SET UP"
on page 11.)

• If those settings do not work properly, please

call our help line on the front page of this owner’s

manual.

2

Use [CH.

K

/

L

] or the Number buttons to

select your desired channel number.

3

Use [VOL.

X

/

Y

] to adjust the volume.

Press [MUTE] to instantly
mute the sound. Press it again
to restore the previous sound
level.

NOTE:

• Even if you turn off the unit in the DVD mode, the unit

will be in the TV mode when you turn it on again.

TO WATCH CABLE OR SATELLITE CHANNEL

If the unit is connected to a cable box or satellite
box, use [CH.

K

/

L

] to select CH3 or CH4 accord-

ing to the output channel setting of the device and
select desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external equipment is
connected to the front AUDIO/
VIDEO input jacks, press
[SELECT] or [CH.

K

/

L

] repeat-

edly until "AUX" appears on the
screen.

- HELPFUL HINTS -

1.PLEASE CHECK TO SEE IF

THE ANTENNA/CABLE/

SATELLITE IS

PROPERLY CONNECTED.

2.DID YOU PERFORM

“AUTO CH PROGRAMMING”?

3.PLEASE REFER TO FRONT

PAGE OF THE OWNER’S

MANUAL OR REAR PANEL

FOR SUPPORT LINE

INFORMATION.

INITIAL SET UP

When you turn on the power for the first time,
the SELECT LANGUAGE screen is displayed.
Select the language for screen display and perform
auto programming of the channels.

1

After antenna or cable connection is
completed, connect the power cord into
a standard AC outlet.

2

Press [STANDBY-ON y] to turn on the unit.

3

Press one of the keys listed
below to select the language
of on-screen menu.

• ENGLISH:

[VOL.

Y

]

• ESPAÑOL: [VOL.

X

]

• FRANÇAIS: [CH.

K

]

4

Confirm the antenna (or cable)
connection and press [PLAY B

B

].

• The tuner scans and

memorizes all active
channels in your area.

5

When the scanning is completed,
the tuner stops on the lowest
memorized channel.

NOTES:

• You can exit the INITIAL SETUP menu by pressing

[SET-UP]. If the button is pressed during channel
scanning, the tuner stops scanning and the lowest
memorized channel is displayed.

The INITIAL SETUP menu is displayed every time

you turn on the unit unless the scanning is com-
pleted.

• In case no channel can be

received by the channel scanning,
"NO TV SIGNALS" is displayed on
the screen. Turn off the unit and
check the antenna connection,
then follow steps 1 to 5 again.

You can change the setting after completing INI-

TIAL SET UP by LANGUAGE menu or CHANNEL
SET UP menu. (Refer to "ON-SCREEN MENU LAN-
GUAGE" or "CHANNEL SET UP" on page 11).

• If there is no signal input from the antenna terminal

and no operation for 15 minutes, the unit will turn itself
off automatically.

CH 15

EN

9

T

V OPERATION AND SETTINGS

TV SECTION

WATCHING A TV PROGRAM

TV

TV

OPERA

TING

CONTR

OLS

AND

FUNCTIONS /

TV OPERA

TION AND SETTINGS

TV SECTION

To use the number buttons

•Single digit channels: (Ex. 02, 03, 04 and so on)

Press [0] first to select a single digit channel.

•Two digit channels: (Ex. 12, 38, 95 ...)

Press two digits directly.

•Tree digit channels: (Ex. 115, 125 ...)

Press [+100] first, then press the last two digits.

SELECT LANGUAGE

ENGLISH

NEXT:PRESS VOLY

H

ESPAÑOL

DESPUÉS:PRESIONE VOL

X

H

FRANÇAIS

APRÈS:PRESSEZ CH.

K

H

– INITIAL SETUP –

PLEASE CONNECT ANTENNA
OR CABLE OR SATELLITE
TO THIS UNIT.
THEN PRESS PLAY,
IN ORDER TO PERFORM
“AUTO CH PROGRAMMING”.

TV

TV

NO TV SIGNALS

(Example)

Advertising