Panasonic WV-CS554 - Manuel (Page 45)

(4) Camera Phase (Hue) Setting (HUE)
1. Move the cursor to HUE. The T cursor appears in inversed video.
2. While observing the vector scope or color video monitor, adjust
the chroma phase (hue) by using the joystick. The cursor moves
to the right or left.
To reset to the factory setup, press the F2 button of the WV*
CU550B.
(For the WV-RM70, keep pressing the Right and Left s\witches
simultaneously for 2 seconds or more.)
(5) BW
Move the cursor to BW and select AUTO, ON or OFF by moving
the joystick to the right or left. Default: OFF
AUTO: The camera selects black and white mode if the picture is
dark, or color mode if the picture is bright enough.
Note: It takes 1 minute to make the selected mode effective
after stopping pan/tilt, zoom or focus.
ON: Black and white mode is selected.
OFF: Color mode is selected.
Note: Mode selection is disabled if ALARM IN 4 is set to BAV
on the Special 1 menu.
(6) BURST(BW) ^2^
Move the cursor to BURST(BW) and select ON or OFF by moving
the joystick to the right or left. Default: ON
ON: The burst signal is supplied along with the black and white
composite video.
OFF: The burst signal is not output.
Note: We recommend that you usually select ON.
(7) Digital Noise Reduction (DNR)
Move the cursor to DNR and select LOW1, LOW2, HIGH1 or
HIGH2 by moving the joystick to the right or left. Default: LOW2
LOW1: Selects a lower effect. The afterimage remains.
LOW2: Selects a lower effect. No afterimage.
HIGH1: Selects a higher effect. The afterimage remains.
HIGH2: Selects a higher effect. No afterimage.
(8) To Restore the Camera Default Position
Move the cursor to REFRESH by using the joystick and press the
F2 button of the WV-CU550B.
(For the WV-RM70, WV-CU360 or WV-CU161, keep pressing the
Right and Left switches simultaneously for 2 seconds or more.)
CHROH& GAIN
XP GAIN
PEDESTAL •I-..........
HUE
- +
BW OFF
BURST(BW) ON
REFRESH -»PUSH SW
CAMERA RESET -^PUSH SW
DNR LOW2
RET
** SPECIALS ••
CHROMA GAIN
AP GAIN
PEDESTAL
-I...........
RUE
-
+
BW ' auto
BURST (BW) ON
REFRESH iPUSH SW
CAMERA RESET iPUSH SW
OMR LOW2
RET
•• SPECIAL! ••
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
•1.......
••••I-"-
+
BW OFF
BURST(BW) ON
REFRESH -*PUSH SW
CAMERA RESET ^PUSH SW
DNR LOH2
RET
•• SPECIAL! **
CHROMA GAIN • • • • I - ” *
AP GAIN
PEDESTAL • 1 ..............
HUE
BW
- +
OFF
BURST(BW) ON
REFRESH -»PUSH SW
CAMERA RESET •4PUSH SW
DNR LOW!]
RET
*• SPECIAL! **
CHROMA GAIN
AP GAIN
PEDESTAL •1.......
HUE
- +
BW OFF
BURST(BW) ON
REFRESH ttPUSH SW
CAMERA RESET -iPUSH SW
DNR
RET LOW!
(9) Camera Resetting
Move the cursor to CAMERA RESET by using the joystick and
press the F3 button of the WV-CU550B.
The camera is reset to the factory preset parameters.
(For the WV-RM70, keep pressing the Right, Left and Set switches
simultaneously for 2 seconds or more. For the WV-CU360 or WV-
CU161, keep pressing the Right and Left switches and the numer­
ic button 5 simultaneously for 2 seconds or more.)
** SPECIAL! **
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
-
BW OFF
BURST(BW) ON
REFRESH -4PUSH SW
CAMERA RESET ^PUSH OT
DNR LOW!
RET
45