Cooper Lighting 6109 Manuel d'utilisation

Motion sensing wall switch, Adjustments specifications troubleshooting use, Installation

Advertising
background image

AUTO

ON

6109

Motion Sensing
Wall Switch

The 6109 Motion Sensing Wall Switch dectects motion to turn on
lights for an adjustable amount of time. A built-in photo cell can be
set to keep lights off when the lights aren't needed. The unit has
excellent sensitivity and a wide 180

0

detection range. It can be used

with incandescent lighting as well as rapid start fluorescent lighting.
Two LEDs allow for easy mode identification. (Not for use with elec-
tronic ballasts)

Installation is as easy as replacing a wall switch. However, some
codes require installation by a qualified electrician.

Features include:
• 180

0

motion detection angle

• Adjustable on-time from 12 sec. to 30 min.
• Adjustable photocell
• Works with incandescent and rapid start fluorescent lighting (Not

for use with electronic ballasts)

• Works with motors up to 1/6 hp.
• Push button selectable ON AND AUTO modes.

WARNING: Turn power off at the circuit breaker before wiring.

TYPICAL INSTALLATION

Control Cover

Plate Removed

to access

adjustments

screws

MODE

Selection

Switch

• Remove the decorative coverplate (secured by two

decorative screws).

• Remove Control Cover (pinch the Control Cover at

the indicated points and pull).

• Remove the existing switch (if this is a retrofit

application).

• Connect the detector as shown in the diagram.

Before installing the detector into the box, make
sure there is no wire exposed at the connection.

• Do not connect to neutral wire or damage to unit will

occur.

If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the customer
service hotline at 1-866-853-4293 between 8:00 AM and 7:00 PM ET weekdays.

Electrical input....................................................................................................................................120V, 60 Hz
Fluorescent Load (not for electronic ballasts).....................(2) 30 Watt minimum 400 Watt maximum Rapid Start
Motor Load........................................ ........................................................................................1/6 HP maximum
Incandescent.............................................................................................................................500W at 120V AC
On-Time...........................................................................................Adjustable approximately 12 sec. to 30 min.
Photocell Sensor..........................................................................................From dull daylight to less than 1 FC.
Coverage.............................................................................up to 20 ft. at 180

0

, up to 40 ft. in front of the sensor

Dimensions .........................................................................................4.10 in. high, 1.7 in. wide and 2.00 in. deep

The length of time that the lights stay on is
adjustable from 12 seconds to 30 minutes.
• Use a small screw driver to set the time by
using the diagram below as a guide.

Replace control panel cover and install the decorative wall plate. In installations where the Cooper motion
sensor switch is combined with other switches or outlets on an expanded box, a combination wall plate will
need to be purchased. Various combination wall plates are available at Home Centers and Electrical Supply
Stores.
Press the push button a couple of times to make sure it operates freely.

When the light in the room is at
the level you want the lights to
turn on, set the switch to the
AUTO position.
Put the TIME control to the 12
sec. (fully counter-clockwise)
position.
Put the LIGHT control to the mini-
mum dark (fully counter-clock-
wise) position.
Wait for the lights to turn off.
Turn the LIGHT adjustment clock-
wise in very small steps and wait
2 seconds before moving your
hand in front of the sensor.
Repeat until the lights controlled
by the sensor come on. The light
will now come on when the light
level is at or below the present
level and motion is detected.

To adjust the photocell:

MODE Selection Switch

Pressing the pushbutton selects one of three modes of operation: ON, OFF, AUTO

ON

: Lights stay on continuously. The ON led is lit.

OFF

: Lights stay off. The AUTO led and the ON led are not lit.

AUTO

: Lights come on for time set when motion is detected and the light level is below the set level.

The AUTO led is on and the ON led is off.

*When in the OFF mode, the circuit is still alive. Turn off circuit breaker before re-lamping.


The sensor can be prevented from turning on lights when
there is already enough light in the room. Use a small
screw driver to set the light level using this
diagram as a guide. In the fully clockwise position, the
sensor turns on lights even in full daylight. In the fully
counter-clockwise poition, the sensor only turns on lights
when the surrounding light level is very low.

ADJUSTMENTS

SPECIFICATIONS

TROUBLESHOOTING

USE

TIME

Complete Installation

LIGHT LEVEL

AUTO

ON

TIME

ON

AUTO

TIME

LIGHT

- 2 -

- 3 -

- 4 -

• Mount the detector into the wall box with the mounting screws.
• For test purposes, use a small screwdriver to turn the time control fully counter-clockwise

and the light control fully clockwise. Turn the power back on at the circuit breaker.

• Press MODE selection push button until the AUTO LED is on. Lamp will be on for 12 seconds. Allow two

minutes for the unit to warm up. If motion is detected, the lights will turn on. The lights will turn off 12 sec-
onds after motion is no longer detected.

(NEUTRAL)

Green

ground wire to

junction box screw or

grounding wire

BLACK

BLACK

HOT

(LINE)

12 Sec.

SYMPTOM

Light does not
come on.

Lights do not
stay on in the
Auto mode.

POSSIBLE CAUSE

Circuit breaker or fuse is turned
off.
If the lamp being controlled has
another switch, it may be turned
off.
Bulb is defective.
LIGHT control is set too far
toward the DARK position.
MODE switch is set to OFF
instead of AUTO.
Incorrect wiring.

Motion has stopped in the room.
TIME control is set for too short a
delay.

1.

2.

3.
4.

5.

6.

1.

2.

SYMPTOM

Light does
not turn off.

Light comes
on for no

reason in

the

Auto mode.

POSSIBLE CAUSE

Incorrect wiring.
MODE switch is set to ON
instead of AUTO.
Motion is still present.
Delay set by TIME control
has not expired.

Heating or cooling ob-
jects (such as air vents,
appliances, or drafts through
the wall box) are causing
false triggering.
Switch on the sensor has
been turned off and back on.
There was a momentary
power interrup-tion. The light
will turn off automatically
when the "on" time expires.

1.
2.

3.
4.

1.

2.

3.

YOUR COOPER WIRING DEVICES ASSEMBLED PRODUCT TWO YEAR LIMITED WARRANTY

For a period of 2 years from the date of purchase, Cooper Wiring Devices will replace or repair the motion
sensing switch provided that it has not been subject to abuse, improper installation or improper use, and is
returned prepaid to Cooper Wiring Devices Quality Control Department at 203 Cooper Circle, Peachtree City,
GA 30269. If the product has been discontinued, replacement will be made with the nearest available equiva-
lent model. This warranty does not cover consumables (such as fuses). Proof of purchase in the form of a
bill of sale or receipted invoice that shows that the item is within the applicable warranty period must be pre-
sented to obtain the repair or replacement provided by the warranty. Repair or replacement as provided
under this warranty is the exclusive remedy of the customer. Cooper Wiring Devices shall not be liable for
any incidental or consequential damages for breach of any express or implied warranty on any of its prod-
ucts. Except to the extent limited or prohibited by applicable law, any implied warranty of merchantability or
fitness for a particular purpose on this product is limited in duration to the duration of this warranty.
Some
states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on
how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.

LIGHTING

LOAD

Pinch

here

Pinch

here

GENERAL APPLICATION INFORMATION

The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.

The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to
avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other
sources of heat or cold.

NEW APPLICATION

Choose a location where the motion sensor has a clear view of
the entire area where occupant motion may occur.

RETROFIT APPLICATION

Motion sensing switch will replace existing wall switch. Use only
where the existing switch location provides a clear view of the
occupied area.

Included are: • The sensor switch • Cover plate • 3 wire connectors • 2 large screws • 2 small screws.

Typical Plan View of Coverage

INSTALLATION

SELECT A LOCATION

40'

20'

0'

WARNING: For indoor use only.

INSTALLING THE SWITCH

Questions? Call 1-866-853-4293 8:00 AM to 7:00 PM Eastern Time, weekdays

T I M E

L I G H T

+

+

Dark (low

light level)

AUTO

LED

Any Light

Level

469MX-PT

LOAD

Note:
Adjustment screws
found under (off-auto-
on) face plate.

30 Min.

598-1179-02 E

Advertising