Attwood Adjustable Spray Aerator Heads Manuel d'utilisation

Aerator spray head

Advertising
background image

©2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

FEATURES

The Attwood single-valve aerator spray head is designed for 3/4" I.D.
hose for side mounting on baitwell or livewell systems with built-in
overflow or recirculating systems. It is made of durable plastic for
corrosion resistance.

The aerator spray head has a rotating knob to adjust and maintain
flow setting from closed to full flow. The knob is designed to stay in
place and not vibrate out. However, it can be removed for cleaning
debris from the spray head.

Models 4125 and 4123 are the same, with this exception: on the 4123,
the hose barb is replaced with the Flow-Rite™ Qwik-Lok™ connector.

Patent No. D.317.347

WARNING

Do not operate 110/120 volt A.C. power tools while boat is in the
water. Remove boat from water before proceeding.

TOOLS AND MATERIALS REQUIRED FOR INSTALLATION

Hose clamp suitable for 3/4" I.D. hose

Screw Driver

Large pair slip joint pliers or large crescent wrench

1-inch drill or hole cutter

MOUNTING INSTRUCTIONS

1. Select and mark the location for spray head.
2. Make a 1-inch hole at the selected location.
3. Remove the nut from the spray head assembly.
4. Place the threaded end of the spray head through the hole so

that the nozzle spray adjuster is inside the livewell. Apply a small
bead of polyurethane marine sealant (such as Silkaflex 231) on
the fixed flange and the nut flange to insure a watertight seal.

5. Screw the nut onto the threads. Tighten the nut approximately

one-quarter turn past full contact.
CAUTION: Do not overtighten nut – threads will strip preventing
a good fit and good water seal.

6. Make sure the hose barb is pointed down.
7. Install hose clamps around hose. Attach hose to hose barb.

Tighten hose clamp.

CARE AND MAINTENANCE

For best results, periodically remove adjusting knob, clean out debris
from spray head, and replace knob.

3

®

Attwood marine hardware, navigational lighting, bilge pumps,
and other marine accessories are specified more than any other
brand by America’s best-known boat manufacturers as original
equipment. Look to Attwood for quality replacement parts and
marine accessories.

SAVE THESE INSTRUCTIONS

Form Number 69278 Rev. C

03-10

Aerator Spray Head

4125, 4123

Flow-Adjustment
Knob

Flange

Hose Barb

Hose Clamp

Hose

Boat Transom

Attwood Aerator
Pump with Strainer
(or equivalent)

Nut

* = Model 4125 only. On Model 4123, use the Flow-Rite

Qwik-Lok

connector.

ATTWOOD LIMITED WARRANTY

Attwood Corporation, 1016 North Monroe, Lowell, Michigan 49331
(“Attwood”) warrants to the original consumer purchaser that Attwood
brand products will be free from defects in materials and workmanship
under normal use and service for one year from the date of original
consumer purchases.

This limited warranty is not applicable if the product has been damaged
by accident, improper installation, unreasonable or improper use, lack
of proper maintenance, unauthorized repairs or modifications, normal
wear and tear, or other causes not arising out of defects in materials
or workmanship.

Attwood products are warranted for use on pleasure boats. Any other
use — including but not limited to commercial, racing, or non-marine
use — are not covered under this warranty. Attwood’s obligation under
this warranty is limited to repair of the product at Attwood’s plant or
replacement of the products at Attwood’s option without expense to
the original consumer purchaser. Any expenses involved in the removal,
reinstallation or transportation of the product are not covered by this
warranty. The product must be returned to Attwood’s plant at the address
above, postage pre-paid, and insured with proof of original purchase
including date. If Attwood is unable to replace the product and repair
is not commercially practical or cannot be timely made, or if the original
consumer purchaser is willing to accept a refund in lieu of repair or
replacement, Attwood may refund the purchase price, less an amount
for depreciation. The acceptance by Attwood of any product returned
or any refund provided by Attwood shall not be deemed an admission
that the product is defective or in violation of any warranty. Products
that are replaced or for which a refund is issued become the property
of Attwood.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESSED
WARRANTY OF THESE PRODUCTS. NO IMPLIED WARRANTY
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE EXTENDED BEYOND THE WARRANTY
PERIOD STATED ABOVE FOR EACH PRODUCT. ATTWOOD
SHALL NOT BE LIABLE FOR ANY DAMAGES, FOR LOSS OF
USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL
OR CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.

Some states do not allow limitations or how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations and exclusions may not apply
to you. This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.

Advertising