Whirlpool WED8900BW - Manuel (Page 5)

5
Control Panel And Features
POWER BUTTON
Press to turn the dryer on and off. Press again to stop/
cancel a cycle at any time.
CYCLE CONTROL KNOB
Use your dryer’s cycle control knob to select available
cycles on your dryer. Turn the knob to select a cycle for your
laundry load. See “Cycle Guide” for detailed descriptions of
cycles.
EST. TIME REMAINING DISPLAY
When you select a cycle, its default settings will light up and
the Estimated Time Remaining (for Automatic Cycles) or
actual time remaining (for Manual Cycles) will be displayed.
DONE/SENSING DISPLAY
Done
This will indicate that the selected cycle has ended and
the load may be removed from the dryer. If the Wrinkle
Shield option has been selected, the dryer may continue
to tumble the load, even if the DONE indicator is lit.
Sensing
At the beginning of an Automatic Cycle, the sensing light
illuminates as the dryer senses the load size and adjusts
for the appropriate dry time for that load. This indicator
will not light during Timed Cycles or with options such
as Wrinkle Shield ™ .
ECO MONITOR
Your dryer is specially designed to conserve energy. Each
cycle, along with selected options, will result in different
energy usage, which will be displayed on the Eco Monitor
bar, allowing you to choose the best energy usage for each
load.
START/PAUSE BUTTON
Press to start a cycle, or press once while a cycle is in
process to pause it.
CYCLE OPTIONS
Use these buttons to select available options for your dryer.
Not all cycles and options are available on all models.
EcoBoost ™ (on some models)
Press to activate EcoBoost ™ option on select Automatic
cycles. The EcoBoost ™ option allows you to increase
your energy savings with minimal impact on cycle dry
times.
NOTE: Selecting the EcoBoost
™ option adds 5 minutes
to the default cycle time.
2
3
4
5
6
7
1
Not all features and cycles are available on all models.
Static Reduce (on some models)
Press to add the Static Reduce option to select cycles
(see Cycle Guide). The dryer will automatically tumble and
spray to introduce a small amount of moisture into the
load to help reduce static. This option adds approximately
8 minutes to the total cycle time.
Damp Dry Signal
When selected, a signal will sound during the drying
cycle when the load is damp but not completely dry. This
will allow you to take clothes out of the load that do not
need to dry completely. This option is available on Heavy
Duty, Normal, Sheets, Active Wear, Towels, Casual, Jeans,
and Delicate cycles. It is a default option for the Bulky
Items cycle.
Wrinkle Shield ™ /Wrinkle Shield ™ with Steam
(on some models)
If you will be unable to remove a load immediately, press
WRINKLE SHIELD ™ to add up to 140 minutes of periodic
tumbling to help reduce wrinkling. On models with Wrinkle
Shield ™ with Steam, a short steam cycle is added after 60
minutes to help smooth out wrinkles.
Cycle Signal
Use this button to turn the signal indicating the end of
a drying cycle on or off, or to adjust the volume of the
signal.
Check Vent Indicator Light
The Check Vent indicator light will come on if a blocked
vent or low airflow issue is detected. For more information
on maintaining good airflow, see “Check Your Vent
System for Good Airflow”.
CYCLE MODIFIERS
Use these buttons to select available modifiers for your
cycles. Not all cycles and modifiers are available on all
models.
Dryness Level
You may adjust the Dryness Level on Automatic Cycles, if
desired.
NOTE: The Dryness Level modifier is for use with
Automatic Cycles only. Not available on the Sanitize
cycle.
Temp
When using Manual Cycles only, you may select a dry
temperature based on the type of load you are drying.
Use the warmest setting safe for the garments in the load.
Follow garment label instructions.
NOTE: Automatic Cycles use a preset temperature
that is not adjustable.
8
1
7
2 3 4 5 6
8