Product data sheets, Interior water filtration system – Whirlpool GI0FSAXVY Manuel d'utilisation

Page 15

Advertising
background image

15

PRODUCT DATA SHEETS

Interior Water Filtration System

Model UKF8001AXX-750 Capacity 750 Gallons (2839 Liters)

This system has been tested according to NSF/ANSI

Standards 42 and 53

for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI

Standards 42 and 53.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to
71.6°F (20°C to 22°C).

It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.

The disposable water filter should be replaced at least every
6 months.

The filter monitor system measures the amount of water that
passes through the filter and alerts you to replace the filter.
When 90% of the filter’s rated life is used, the yellow (Order)
light comes on. When 100% of the filter’s rated life is used, the
red (Replace) light comes on, and it is recommended that you
replace the filter. For models without filter status lights,
replace the filter every 6 months. Use replacement filter
model UKF8001AXX-750. 2008 suggested retail price of
$44.99 U.S.A./$49.95 Canada. Prices are subject to change
without notice.

The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.

Refer to the “Water Filtration System” section for the
Manufacturer’s name and telephone number.

Refer to the “Warranty” section for the Manufacturer’s limited
warranty.

Application Guidelines/Water Supply Parameters

System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate
Class I*; and against NSF/ANSI Standard 53 for the reduction of
Lead, Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran,
Toxaphene, Cysts, Turbidity, Asbestos and Lindane.

Substance Reduction
Aesthetic Effects

NSF Reduction
Requirements

Average
Influent

Influent Challenge
Concentration

Maximum
Effluent

Average
Effluent

Minimum%
Reduction

Average%
Reduction

Chlorine Taste/Odor
Particulate Class I

*

50% reduction
85% reduction

1.88 mg/L
5,700,000 #/mL

2.0 mg/L ± 10%
At least 10,000
particles/mL

0.06 mg/L
69,000 #/mL

**

0.05 mg/L
30,583 #/mL

96.84
98.94

>97.26
99.52

Contaminant
Reduction

NSF Reduction
Requirements

Average
Influent

Influent Challenge
Concentration

Maximum
Effluent

Average
Effluent

Minimum%
Reduction

Average%
Reduction

Lead: @ pH 6.5
Lead: @ pH 8.5

0.010 mg/L
0.010 mg/L

0.153 mg/L

0.150 mg/L

0.15 mg/L ± 10%
0.15 mg/L ± 10%

< 0.001mg/L
< 0.001mg/L

< 0.001mg/L
< 0.001mg/L

>99.29%
>99.29%

>99.35%
>99.33%

Mercury: @ pH 6.5
Mercury: @ pH 8.5

0.002 mg/L
0.002 mg/L

0.006 mg/L
0.006 mg/L

0.006 mg/L ± 10%
0.006 mg/L ± 10%

0.0005 mg/L
0.0015 mg/L

0.0003 mg/L
0.0008 mg/L

90.91
75.93

95.70
86.22

Benzene

0.005 mg/L

0.014 mg/L

0.015 mg/L ± 10%

0.0011 mg/L

0.0006 mg/L

92.14%

95.71%

p-Dichlorobenzene

0.075 mg/L

0.208 mg/L

0.225 mg/L ± 10%

< 0.0005 mg/L

< 0.0005 mg/L 99.74%

99.76%

Carbofuran

0.04 mg/L

0.081 mg/L

0.08 mg/L ± 10%

< 0.001mg/L

< 0.001mg/L

98.46%

98.74%

Toxaphene

0.003 mg/L

0.015 mg/L

0.015 ± 10%

< 0.001mg/L

< 0.001mg/L

91.67%

92.97%

Atrazine

0.003 mg/L

0.009mg/L

0.009 mg/L ± 10%

< 0.002 mg/L

< 0.002 mg/L 75.31%

76.99%

Asbestos

99%

155 MF/L

10

7

to 10

8

fibers/L

††

< 1 MF/L

< 1 MF/L

>99.99%

>99.99%

Live Cysts

Turbidity

>99.95%
0.5 NTU

166,500 #/L
10.7 NTU

50,000/L min.
11 ± 1 NTU

< 1 #/L

0.49 NTU

< 1 #/L

0.31 NTU

>99.99
95.2

>99.99
97.09

Lindane

0.0002 mg/L

0.002 mg/L

0.002 ± 10%

< 0.0001mg/L

0.000 mg/L

96.50%

98.72%

Water Supply
Water Pressure
Water Temperature
Service Flow Rate

City or Well
35 - 120 psi (241 - 827 kPa)
33° - 100°F (1° - 38°C)
0.78 gpm (2.9 L/min.) @ 60 psi

*

**

††

Class I particle size: >0.5 to <1 um
Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.
Fibers greater than 10 um in length
Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

Advertising