Sony CDX-CA710X Manuel d'utilisation

Fm / am compact disc player, 2a b, Cdx-ca710x

Advertising
background image

BUS CONTROL IN

BUS AUDIO IN

Source selector*
Sélecteur de source*

XA-C30

* not supplied

non fourni

Sony Corporation © 2003

Printed in Thailand

3-247-406-11

(1)

Cautions

• This unit is designed for negative ground 12 V DC

operation only.

• Do not get the wires under a screw, or caught in

moving parts (e.g. seat railing).

• Before making connections, turn the car ignition

off to avoid short circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

Run all ground wires to a common ground

point.

• Be sure to insulate any loose unconnected wires

with electrical tape for safety.

• The use of optical instruments with this product

will increase eye hazard.

Notes on the power supply cord (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

• The numbers in the list are keyed to those in the

instructions.

• The bracket 1 and the protection collar 3 are

attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.

Keep the release keys 5 for future use as they

are also necessary if you remove the unit from
your car.

Caution

Handle the bracket 1 carefully to avoid injuring
your fingers.

Note
Before installing, make sure that the catches on both
sides of the bracket
1 are bent inwards 2 mm (

3

/

32

in). If

the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.

Installation/Connections

Installation/Connexions

FM/AM
Compact Disc
Player

Connection example (2)

Notes (2-A)
• Be sure to connect the ground cord before connecting

the amplifier.

• If you connect an optional power amplifier and do not

use the built-in amplifier, the beep sound will be
deactivated.

Tip (2-B-

)

For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.

Connection diagram (3)

1

To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.

2

To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no

power antenna or antenna booster, or with a
manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the interface cable of a car telephone

5

To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12

V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

6

To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal
surface of the car first.

Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V

DC when you turn on the tuner.

• When your car has built-in FM/AM antenna in the rear/

side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.

• A power antenna without relay box cannot be used

with this unit.

2

A

B

AUDIO OUT REAR

BUS AUDIO IN

BUS CONTROL IN

1

4

5

Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)

Rear speaker
Haut-parleur arrière

Front speaker
Haut-parleur avant

1

CD/MD changer
Changeur de CD/MD

Rotary commander RM-X4S
Satellite de commande RM-X4S

Power amplifier
Amplificateur de puissance

×

4

2

3

CDX-CA710X

×

2

1

Catch

Advertising