Sony CDX-L510X Manuel d'utilisation

Fm / am compact disc player, 2a b, Cdx-l510x

Advertising
background image

Sony Corporation © 2003

Printed in Korea

3-247-736-11

(1)

Cautions

• This unit is designed for negative ground 12 V DC

operation only.

• Do not get the wires under a screw, or caught in

moving parts (e.g. seat railing).

• Before making connections, turn the car ignition

off to avoid short circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

Run all ground wires to a common ground

point.

• Be sure to insulate any loose unconnected wires

with electrical tape for safety.

• The use of optical instruments with this product

will increase eye hazard.

Notes on the power supply cord (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

• The numbers in the list are keyed to those in the

instructions.

• The bracket 1 and the protection collar 3 are

attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.

Keep the release keys 5 for future use as they

are also necessary if you remove the unit from
your car.

Caution

Handle the bracket 1 carefully to avoid injuring
your fingers.

Note
Before installing, make sure that the catches on both
sides of the bracket

1

are bent inwards 2 mm (

3

/

32

in). If

the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.

Installation/Connections

Installation/Connexions

FM/AM
Compact Disc
Player

Connection example (2)

Notes (2-B)
• Be sure to connect the ground cord before

connecting the amplifier.

• If you connect an optional power amplifier and do

not use the built-in amplifier, the beep sound will
be deactivated.

Connection diagram (3)

1

To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.

2

To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is

no power antenna or antenna booster, or with
a manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control
and power supply leads.”

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the

+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control
and power supply leads.”

5

To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a
metal surface of the car first.

2

A

B

AUDIO OUT REAR

1

4

5

Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)

Rear speaker
Haut-parleur arrière

Front speaker
Haut-parleur avant

1

Power amplifier
Amplificateur de puissance

Rotary commander RM-X4S
Satellite de commande RM-X4S

Ч

4

2

Ч

2

3

CDX-L510X

1

Catch

Advertising