Sony PEGA-GC10 - Manuel

1 Tap the [GameCon] icon on the Home screen.
The Game Controller’s General settings screen appears.
2 Tap V in the upper right corner of the General
settings screen, and select [Keys 1] or [Keys 2]
screen.
The key assignment settings screen appears.
*
You can reassign the [Keys 2] buttons only when you
play games that support the extended buttons.
3 Tap V to the right of each button, and change
the assignment.
Installing the supplied
game software
Install the game application from the supplied installation
CD-ROM on your CLIÉ handheld, following the procedure
below. For details on how to play the game, refer to the
directions included in the installation CD-ROM.
1 Insert the supplied installation CD-ROM into
the CD-ROM drive of your PC.
The initial installation screen appears.
2 Click [English].
The installer screen appears.
3 Click [Install Game].
The installer submenu appears.
4 Install the software, following the instructions
shown on the screen.
If you have registered more than one user, select a user
name from the user list.
5 Click [Done].
6 Perform a HotSync ® operation on your CLIÉ
handheld.
A HotSync operation starts and the software is
transmitted from your Windows
® PC to your CLIÉ
handheld.
For customers in USA and Canada
Tip
In addition to this game application you have just installed in the
above procedure, the supplied installation CD-ROM includes the
trial versions of some other game applications. You can try them by
installing them on your CLIÉ handheld as follows.
1
Insert the supplied installation CD-ROM into the CD-ROM drive
of your PC.
2 Copy the file of the game you want to try on your PC from
[¥3rdparty¥Games] in the CD-ROM.
3 Install the game application on your CLIÉ handheld, following the
instructions for your CLIÉ handheld.
Note
For details on the supplied game applications, contact the
manufacturer of each game application.
Specifications
Input DC 3V
Power consumption 7.5 mW
(during normal operation)
0.24 mW
(with HOLD function set)
Operating temperature 41 ˚F to 95 ˚F (5 ˚C to 35 ˚C)
Dimensions
3 5 / 8
Ч 29 / 32
Ч 1 11 / 16 inches
(89 Ч 22.5 Ч 42.5 mm) (w/h/d)
(Excluding the largest projecting
part)
Mass. Approx. 1.23 oz (35 g)
Cord length Approx. 2 3 / 8 inches (60 mm)
(1 3 / 16 inches (30 mm) at the
factory settings)
Accessories Installation CD-ROM
Case
Strap
Design and specifications are subject to change without
notice.
Notes on use
• Do not subject the unit to:
– Extreme heat or cold
– Dust, dirt, or sand
– High humidity
– Vibration
– Strong magnetic fields
– Mechanical shock
– Direct sunlight (for extended periods of time)
• Do not drop the unit.
• Be sure that nothing metallic comes into contact with the
metal parts of this unit. If this happens, a short circuit
may occur and the unit may be damaged.
• Do not operate the unit if it has a damaged cord or if it
has been dropped or damaged.
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
• While the unit is in use, it gets warm. This is normal.
Cleaning
Clean the unit with a soft, dry cloth or a soft cloth lightly
moistened with a mild detergent solution. Do not use any
type of solvent, such as alcohol or benzine, which may
damage the finish.
Before use
This Game Controller is adaptable only for Sony CLIÉ
handheld.
Installing the software
Before using the Game Controller, install a driver for Game
Controller from the supplied installation CD-ROM on your
CLIÉ handheld.
For installation, you need a Microsoft
® Windows ®
compatible computer on which the Palm Desktop software
that is suitable for your CLIÉ handheld has been installed.
Connect the PC to your CLIÉ handheld, and make sure that
HotSync works on both the PC and CLIÉ handheld.
1 Insert the supplied installation CD-ROM into
the CD-ROM drive of your PC.
The initial installation screen appears.
2 Click [English].
The installer screen appears.
3 Click [Install Game Controller software].
The installer submenu appears.
4 Install the software, following the
instructions shown on the screen.
If you have registered more than one user, select a user
name from the user list.
5 Click [Done].
6 Perform a HotSync ® operation on your CLIÉ
handheld.
A HotSync operation starts and the software is
transmitted from your Windows
® compatible computer
to CLIÉ handheld.
Extending the cord
Detaching the cover on the back of the Game Controller
lengthens the cord by about 1
3 / 16 in. (30 mm).
1 Detach the cover on the back of the Game Controller
and extend the cord as shown.
2 Put the cover back in its place.
Attaching the Game
Controller to your CLIÉ
handheld
1 Attach the Game Controller to the CLIÉ
handheld, as if to put it onto the CLIÉ
handheld, as shown.
When you have a Flip&Rotate style CLIÉ
handheld
Attach the Game Controller by sliding it alongside your
CLIÉ handheld, as shown.
Note
The Game Controller cannot be attached to the
Flip&Rotate style CLIÉ handheld when it is set to the
opened style. To use the Game Controller with a
Flip&Rotate style CLIÉ handheld, set the CLIÉ handheld
to the turned style.
2 Hook up the connector of the Game
Controller to the interface connector of the
CLIÉ handheld.
3 Attach the drop-prevention strap to the Game
Controller and CLIÉ handheld.
Game Controller
PEGA-GC10
4-667-427-13(1)
Operating Instructions
Mode d’emploi
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-
free vegetable oil based ink.
Removing the Game Controller
1
Remove the Game Controller while pressing the
center portion on the connector of the Game
Controller, as shown.
2 Remove the drop-prevention strap by pressing the
retaining points on both sides.
z Be sure to attach the drop-prevention strap
when you use the Game Controller.
The CLIÉ handheld and Game Controller are easily detachable. To
prevent injury or damage, be sure to use the strap.
Using the Game Controller
1 Press the POWER button on the CLIÉ handheld
to turn the power on.
2 Tap the [GameCon] icon on the Home screen.
The Game Controller’s General settings screen appears.
3 Tap the check box of [Enable Game Controller]
to tick the item on the General settings
screen.
The Game Controller is ready to use now.
When you do not use the Game Controller
temporarily
Tap the check box of [Enable Game Controller] to remove
the tick on the General settings screen.
Setting the Key Emulation
Tap the check box of [Enable Key Emulation] to tick the item
on the General settings screen. This allows the applications
that are assigned to each button of this unit to start.
Note
If the game does not work correctly, tap the check box of [Enable
Key Emulation] to remove the checkmark on the item and see if the
game works correctly.
Carrying your CLIÉ handheld with the
Game Controller attached
Slide the HOLD switch to the right to set the HOLD
function on the Game Controller. The Game Controller does
not accept any key operations and prevents inadvertent
operation.
When you use the Game Controller again, slide the HOLD
switch to the left to cancel the HOLD function.
Note
When you do not use the Game Controller, remove it from the CLIÉ
handheld.
Location of controls
* The functions of the keys may vary depending on games.
Changing the key assignment
According to the game you play, you can assign the
functions of the buttons and Jog Dial
TM navigator of your
CLIÉ handheld to the keys of the Game Controller.
At the factory default presetting, the functions are assigned
as follows.
f
key: Up button
F key: Down button
g key: Date Book button
G key: Address Book button
A key: To Do List button
B key : Memo Pad button
X/Y + f key: Rotates the Jog Dial navigator upward.
X/Y + F key: Rotates the Jog Dial navigator downward.
X/Y + g key: Presses the Back button.
X/Y + G key: Presses the Jog Dial navigator.
English
WARNING
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Owner’s Record
The model and lot numbers are located on the bottom of
your Game Controller. Record the lot number in the space
provided below. Refer to the model and lot numbers when
you call your Sony dealer regarding this product.
Model No. PEGA-GC10
Lot No.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
any interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
If you have a question about this product, call the Sony
Customer Information Center at keep on next line 1-877-760-
7669; or write to the Sony Customer Information Center at
12451 Gateway Boulevard, Fort Myers, FL 33913. The
number below is for FCC-related matters only.
Declaration of Conformity
Trade Name: SONY
Model No.: PEGA-GC10
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road, Oradell,
NJ 07649 USA
Telephone No.: 201-930-6972
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
The supplied interface cable must be used with the
equipment in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
For customers in the European Countries
This device complies with the following European
Directives:
89/336/EEC, 92/31/EEC (EMC Directives)
93/68/EEC (CE Marking Directive)
This product complies with EN 55022 Class B and EN 55024
for use in the following areas: residential, commercial and
light industrial.
For customers in Canada
This Class B digital apparatus complies with Canadian
ICES-003.
• CLIÉ and Jog Dial are trademarks of Sony Corporation.
• All other trademarks are trademarks of their respective
owners.
Detach the cover.
Extend the code.
The grafitti area
should be covered by
the Game Controller.
Press down firmly.
Interface connector
To detach, press
the retaining
points on both
sides.
X key HOME key MENU key Y key
f/F/g/G
keys
HOLD
switch A key B key
HOLD
ON HOLD
OFF
Sony Corporation © 2002 Printed in Japan