Sony SA-W3000 Manuel d'utilisation

Sa-w3000

Advertising
background image

©2012 Sony Corporation

Printed in Malaysia

Precautions

On safety

Before operating the subwoofer, be sure that the

operating voltage of your subwoofer is identical with

that of your local power supply.

Unplug the subwoofer from the wall outlet if it is

not to be used for an extended period of time. To

disconnect the cord, pull the cord by grasping the

plug. Never pull the cord itself.

Should any liquid or solid object fall into the

subwoofer, unplug the subwoofer and have the

subwoofer checked by qualified personnel before

operating it any further.

AC power cord must be changed only at the qualified

service shop.

When turning on or off an amplifier or other

equipment

Lower the volume of the amplifier to minimum.
To avoid damaging the subwoofer

Be careful in setting the volume control of the

amplifier to avoid an excessive input power.

Do not attempt to open the enclosure or remove

speaker units and networks.

Do not press the dust cap intentionally or

unintentionally.

In case color irregularity is observed on the

nearby TV screen

With the magnetically shielded type of the speaker

system, the subwoofer can be installed near a TV set.

However, color irregularity may still be observed on

the TV screen depending on the type of your TV set.
If color irregularity is observed...

t

Turn off the TV set once, then turn it on after 15

to 30 minutes.

If color irregularity is observed again...

t

Place the subwoofer further apart from the TV

set.

When howling occurs

Relocate the speaker or turn down the volume of the

amplifier.
On installation

Do not install the subwoofer near heat sources such

as radiators or air ducts, or in a place subject to direct

sunlight, excessive dust, mechanical vibration or

shock.

Good ventilation is essential to prevent internal heat

build-up in the subwoofer. Place the subwoofer in a

location with adequate air circulation. Do not place

the subwoofer on a soft surface or too close to a wall

as this may obstruct the ventilation hole on the back.

Use caution when placing the subwoofer on a

specially treated (waxed, oiled, polished, etc.) floor, as

staining or discoloration may result.

Take care to avoid any possible injury on the corners

of the subwoofer.

On cleaning the cabinet

Clean the cabinet with a soft cloth lightly moistened

with water. Do not use any type of abrasive pad,

scouring powder or solvent such as alcohol or benzine.

If you have any questions or problems

concerning your subwoofer that is not covered

in this manual, please consult your nearest Sony

dealer.

Installation

Since the human ear cannot detect the direction and

position where the bass sound being reproduced by a

subwoofer (below 200 Hz) comes from, you can install

the subwoofer wherever you like in your room.

To obtain a better bass reproduction, we recommend

you to install the subwoofer on a solid floor where the

resonance is unlikely to occur.

You can obtain a sufficient heavy bass reproduction

from a single subwoofer.

However if you use a couple of the subwoofers, you can

obtain an even more effective heavy bass reproduction.

Notes

Always install the subwoofer vertically, keeping a few

centimeters away from the wall.

Do not place an object on the subwoofer or sit on it.

If the subwoofer is installed in the center of a room,

the bass could be extremely weakened. This is due to

the influence of the standing wave of the room. If this

happened, move the subwoofer away from the center

of a room or eliminate the cause of the standing

wave, by installing a bookshelf on the wall, etc.


Hooking Up the System

Overview

Use the LINE IN jacks or the SPEAKER IN

terminals of the subwoofer when you connect the

amplifier. ()

If your amplifier has one of the following types

of output jacks, connect the LINE IN jack and

the amplifier’s jack using the supplied audio

connecting cord.

MONO OUT jack

MIX OUT jack

SUBWOOFER output jack(s)

SUPER WOOFER output jack(s)

If your amplifier does not have the above

mentioned output jacks, connect the speaker

terminals of the amplifier to the SPEAKER IN

terminals instead.

Before you get started

Turn off the power of the amplifier and the

subwoofer before making any connection.

Use the audio connecting cords that are

supplied to the respective equipment. If there

are not enough audio connecting cords to

make the necessary connections, you need

to purchase some optional audio connecting

cords.

Be sure to make connections firmly to avoid

noise.

Connect the AC power cord from the

subwoofer to a wall outlet.

You cannot connect the CENTER output jack

for use with Dolby Pro Logic function to the

subwoofer. Bass sound is not output with some

Dolby Pro Logic modes.

Connecting to an amplifier with a single
set of speaker terminals

Connect the subwoofer to the amplifier and then

connect the front speakers to the subwoofer.

1

Connect the subwoofer to the amplifier.

()
Connect the SPEAKER IN terminals of

the subwoofer to the amplifier’s speaker

terminals with the speaker cords. Be sure to

connect both L and R channels.

2

Connect the front speakers to the

subwoofer. ()
Connect the speakers to the SPEAKER OUT

terminals of the subwoofer.

Connecting to an amplifier with double
(A + B) sets of speaker terminals

If your amplifier has double (A + B) sets of

speaker terminals, connect both the subwoofer

and the front speakers to the amplifier.

1

Connect the front speakers to the

amplifier. ()
Connect the speakers to your amplifier’s

SPEAKER A terminals.

2

Connect the subwoofer to the amplifier.

()
Connect the SPEAKER IN terminals of the

subwoofer to the amplifier’s SPEAKER B

terminals using speaker cords (not supplied).

When using the double (A + B) sets of speakers,

make sure that you select the “A + B” position

with your amplifier.

Note

When you are using SPEAKER A terminals only (front

speaker only) or when the power of the amplifier is

turned off, turn down the volume or turn off the power

of the subwoofer otherwise, hum noise may be heard.

Connecting to an amplifier with a
special jack for a subwoofer

If your amplifier has a special jack for a

subwoofer (like a MONO OUT jack, MIX OUT

jack, SUBWOOFER jack or SUPER WOOFER

jack), connect the LINE IN jack of the subwoofer

to one of those jacks using the supplied audio

connecting cord. ()

Hookups

Connect the MONO OUT jack of your amplifier

to the LINE IN jack of the subwoofer with the

supplied audio connecting cord. ()

Note

If the output level of your amplifier is not large enough,

the sound may not be loud enough. In this case,

connect the speaker terminals of the amplifier directly

to the SPEAKER IN terminals of the subwoofer.

English

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or moisture.

To reduce the risk of fire, do not cover the ventilation

opening of the apparatus with newspapers, tablecloths,

curtains, etc.

Do not place the naked flame sources such as lighted

candles on the apparatus.

To reduce the risk of fire or electric shock, do not

expose this apparatus to dripping or splashing, and do

not place objects filled with liquids, such as vases, on

the apparatus.

To prevent injury, this apparatus must be securely

attached to the floor/wall in accordance with the

installation instructions.

Do not install the appliance in a confined space, such as

a bookcase or built-in cabinet.

The unit is not disconnected from the mains as long as

it is connected to the AC outlet, even if the unit itself

has been turned off.

As the main plug is used to disconnect the unit from

the mains, connect the unit to an easily accessible

AC outlet. Should you notice an abnormality in the

unit, disconnect the main plug from the AC outlet

immediately.

The mains switch is located on the rear exterior.
For customers in the United States

Owner’s Record

The model and serial numbers are located on the rear of

the unit. Record these numbers in the space provided

below. Refer to them whenever you call upon your Sony

dealer regarding this product.
Model No.
Serial No.

This symbol is intended to alert the user

to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.
This symbol is intended to alert the user

to the presence of important operating

and maintenance (servicing)

instructions in the literature

accompanying the appliance.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

To reduce the risk of electric shock, the speaker cord

should be connected to the apparatus and the speakers

in accordance with the following instructions.

1. Disconnect the AC power cord from the MAINS.

2. Strip 10 to 15 mm of the wire insulation of the

speaker cord.

3. Connect the speaker cord to the apparatus and the

speakers carefully so as not to touch the core of

speaker cord by hand.

Also disconnect the AC power cord from the MAINS

before disconnecting the speaker cord from the

apparatus and the speakers.

Installation

Comme l’oreille humaine ne peut pas détecter la

direction ni la position des basses reproduites par un

caisson de grave (en dessous de 200 Hz), vous pouvez

installer le caisson où vous voulez dans la pièce. Pour

Pour

obtenir une meilleure reproduction du grave, il est

toutefois conseillé de l’installer sur un sol ferme, où la

résonnance est peu probable.

Vous pouvez obtenir suffisamment de grave à partir

d’un seul caisson.

Toutefois, si vous utilisez plusieurs caissons de grave,

les basses seront naturellement plus puissantes.

Remarques

Installez toujours le caisson à la verticale et à

plusieurs centimètres du mur.

Ne pas poser d’objet sur le caisson ni s’asseoir dessus.

Si le caisson est installé au centre d’une pièce, le

son grave est extrêmement affaibli. Ce phénomème

est dû aux ondes stationnaires de la pièce. Le cas

échéant, éloignez le caisson du centre de la pièce,

ou éliminez la cause des ondes stationnaires, en

installant, par exemple, une étagère.

Raccordement du système

Aperçu

Utilisez les prises LINE IN ou les bornes

SPEAKER IN du caisson quand vous raccordez

l’amplificateur. ()

Si votre amplificateur comporte l’un

des modèles de prises de sortie suivants,

raccordez-la à la prise LINE IN et la prise de

l’amplificateur à l’aide du câble de connexion

audio fourni.

Prise MONO OUT

Prise MIX OUT

Prise(s) de sortie SUBWOOFER

Prise(s) de sortie SUPER WOOFER

Si l’amplificateur n’offre aucune des prises de

sortie indiquées, reliez les bornes d’enceintes de

l’amplificateur aux bornes SPEAKER IN.

Avant de commencer

Eteignez l’amplificateur et le caisson de grave

avant de les relier.

Utilisez les cordons audio fournis avec les

différents appareils. Si vous n’avez pas assez de

cordons pour faire les liaisons nécessaires, vous

devrez acheter des cordons de liaison audio en

option.

Veillez à insérer à fond les fiches dans les prises

pour éviter toute source de parasites.

Branchez le cordon d’alimentation secteur du

caisson sur une prise murale.

Vous ne pouvez pas relier la prise de sortie

CENTER à ce caisson pour utiliser la fonction

Dolby Pro Logic. Le son grave n’est pas fourni

par certains modes Dolby Pro Logic.

Raccordement à un amplificateur avec
une seule paire de bornes d’enceintes

Raccordez le caisson de grave à l’amplificateur,

puis les enceintes avant au caisson de grave.

1

Raccordez le caisson de grave à

l’amplificateur. ()
Raccordez les bornes SPEAKER IN

du caisson aux bornes d’enceintes de

l’amplificateur avec les cordons d’enceintes.

Veillez à raccorder les canaux gauche (L) et

droit (R).

2

Raccordez les enceintes avant au caisson

de grave. ()
Raccordez les enceintes aux bornes

SPEAKER OUT du caisson de grave.


Raccordement à un amplificateur
avec double paire (A + B) de bornes
d’enceintes

Si votre amplificateur possède une double

paire de bornes d’enceintes (A + B), raccordez

le caisson de grave et les enceintes avant à

l’amplificateur.

1

Raccordez les enceintes avant à

l’amplificateur. ()
Raccordez les enceintes aux bornes

SPEAKER A de votre amplificateur.

2

Raccordez le caisson de grave à

l’amplificateur. ()
Raccordez les bornes SPEAKER IN du

caisson de grave aux bornes SPEAKER B de

l’amplificateur avec des cordons d’enceintes

(non fournis).

Quand vous utilisez la double paire de prises

(A + B), veillez à sélectionner la position

« A + B » sur l’amplificateur.

Remarque

Lorsque vous utilisez les bornes SPEAKER A seulement

(enceintes avant seulement) ou lorsque l’amplificateur

est éteint, réduisez le volume du caisson de grave, ou

éteignez-le, sinon du bruit sera audible.

Raccordement à un amplificateur doté
d’une prise spéciale pour caisson de
grave

Si votre amplificateur comporte une prise

spéciale pour caisson de grave (comme une prise

MONO OUT, MIX OUT, SUBWOOFER ou

SUPER WOOFER), raccordez la prise LINE IN

du caisson à l’une de ces prises à l’aide du câble

de connexion audio fourni. ()

Raccordements

Raccordez la prise MONO OUT de votre

amplificateur à la prise LINE IN du haut-parleur

à l’aide du câble de connexion audio fourni. ()

Remarque

Si le niveau de sortie de l’amplificateur n’est pas

suffisant, le son peut ne pas être assez puissant. Dans

ce cas, reliez les bornes d’enceintes de l’amplificateur

directement aux bornes SPEAKER IN du caisson.

Français

AVERTISSEMENT

Pour éviter tout risque d’incendie ou de choc

électrique, n’exposez pas l’appareil à la pluie

ou à l’humidité.

Pour eviter tout risque d’incendie, ne couvrez pas les

ailettes de ventilation de cet appareil avec des papiers

journaux, des nappes, des rideaux, etc.

Ne placez de sources de flammes nues telles que des

bougies allumees sur l’appareil.

Pour eviter tout risque d’incendie ou de choc

electrique, n’exposez pas l’appareil a des gouttelettes ou

a des eclaboussures et ne posez pa d’objets contenant

du liquide, comme des vases, sur l’appareil.

Pour eviter les blessures, cet appareil doit etre

fermement fixe au sol/mur, conformement aux

instructions d’installation.

N’installez pas l’appareil dans un espace confine, tel

qu’une bibliotheque ou un meuble encastre.

L’appareil n’est pas debranche de la source

d’alimentation secteur tant qu’il reste raccorde a la

prise secteur, meme s’il est eteint.

La fiche principale etant utilisee pour debrancher

l’appareil de la source d’alimentation secteur, raccordez

l’appareil sur une prise secteur facilement accessible.

Si vous constatez que l’appareil ne fonctionne pas

normalement, debranchez immediatement la fiche

principale de la prise secteur.

L’interrupteur d’alimentation se trouve au dos a

l’exterieur.

Précautions

Sécurité

Avant d’utiliser le caisson de grave, vérifiez que sa

tension de fonctionnement est identique à celle du

secteur local.

Si vous prévoyez de ne pas utiliser le caisson pendant

longtemps, débranchez-le de la prise murale. Pour

débrancher le cordon d’alimentation secteur, tirez sur

la fiche. Ne jamais tirer sur le cordon proprement dit.

Si un liquide ou un solide tombait dans le coffret,

débranchez le caisson et faites-le contrôler par un

technicien qualifié avant de le remettre en service.

Le cordon d’alimentation secteur doit être changé par

un professionnel seulement.

Avant d’allumer ou d’éteindre l’amplificateur

ou un autre appareil

N’oubliez pas de baisser complètement le volume.
Pour éviter d’endommager le caisson de grave

Réglez avec soin le volume de l’amplificateur pour

éviter toute entrée de son excessive.

Ne pas essayer d’ouvrir le coffret ou de modifier les

haut-parleurs et les circuits.

Ne pas appuyer sur le cache-poussière, ni

intentionnellement ni par erreur.

Si vous observez des anomalies de couleurs

sur l’écran du téléviseur installé à proximité du

caisson

Le caisson de graves peut être installé près d’un

téléviseur car ce système acoustique est à blindage

magnétique. Mais il est possible d’observer des

anomalies de couleurs avec certains types de téléviseur.
Si vous observez des anomalies de couleurs...

t

Eteignez le téléviseur, puis rallumez-le 15 à

30 minutes plus tard.

S’il n’y a aucun changement...

t

Placez le caisson de graves un peu à l’écart du

téléviseur.

En cas de réaction acoustique

Changez l’emplacement des enceintes ou baissez le

volume de l’amplificateur.
Installation

Ne pas installer le caisson de grave près d’une source

de chaleur, comme un radiateur ou une bouche d’air

chaud, dans un endroit en plein soleil ou exposé à de

la poussière, des vibrations ou des chocs mécaniques.

Une bonne ventilation est essentielle pour éviter une

surchauffe interne du caisson. Installez le caisson

dans un endroit où la circulation d’air est suffisante.

Ne pas l’installer sur une surface molle ou trop près

d’un mur pour ne pas boucher l’orifice de ventilation

à l’arrière du caisson.

Faites attention si le caisson de graves doit être posé

sur une sol traité (ciré, huilé, poli, etc.) car il peut salir

ou décolorer le sol.

Veillez à ne pas vous blesser en heurtant les coins du

caisson.

Nettoyage du coffret

Nettoyez le coffret avec un chiffon doux légèrement

imprégné d’eau. Ne pas utiliser de tampons abrasifs,

poudre à récurer ou diluant, comme l’alcool ou la

benzine.

Pour toute question ou problème au sujet

du caisson de grave, veuillez contacter votre

revendeur Sony le plus proche.

(1)

Active Subwoofer

SA-W3000

4-423-064-11(1)

LINE

OUT

L

L

R

R

IN

OUT

IN

SPEAKER

LINE IN

SPEAKER IN

Amplifier

Amplificateur

SPEAKER

OUT

L

L

R

R

IN

SPEAKER

This subwoofer

Caisson de grave

l

: Signal flow

Sens du signal

OUT

L

L

R

R

IN

SPEAKER

This subwoofer

Caisson de grave

l

: Signal flow

Sens du signal

SPEAKER A

Front

speaker (R)

Enceinte

avant (D)

Front

speaker (R)

Enceinte

avant (D)

Front

speaker (L)

Enceinte

avant (G)

l

: Signal flow

Sens du signal

Front

speaker (L)

Enceinte

avant (G)

SPEAKER B

OUT

L

L

R

R

IN

SPEAKER

Amplifier

Amplificateur

This subwoofer

Caisson de grave

l

: Signal flow

Sens du signal

MONO OUT

LINE

OUT

IN

Amplifier

Amplificateur

This subwoofer

Caisson de grave

l

: Signal flow

Sens du signal

Amplifier

Amplificateur

Advertising