Controlled Products Systems Group 375LM Manuel d'utilisation

Stop, Dip switch smart/learn button, Dip switch

Advertising
background image

MODELS 375LM & 375LMC

Universal Remote Control

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to

operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there

are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit

anyone to cross path of moving gate or door.

© 2008, The Chamberlain Group, Inc.

114A3492B

All Rights Reserved

Read instructions thoroughly BEFORE beginning.

Start with garage door closed. Identify garage door opener type - Smart/
Learn button or DIP Switch. Smart/Learn button or DIP Switches are
located on motor unit or external receiver.

Refer to owner’s manual if necessary.

Proceed with instructions according to your type of garage door opener.

ON

2

3

1

KG

KG

NOTE:
2 Position DIP Switch:
If programming fails reverse
DIP switches (OFF to ON and
ON to OFF).

**3 Position DIP Switch:
For Chamberlain remotes DO NOT
use the “0” position, use “+” or “-”.
If you already have a 3-button
remote, DIP switch #1 must be set to
“-” if the large button is to open the door. It may be
necessary to reprogram original remote controls.

2

12

11

10

9

8

5

3

7

6

4

1

2

Clicker Remote

Existing Remote

3

4

Press program button
until LED lights.

5

Match DIP switches. Turn
extra switches OFF.**

OR

DIP SWITCH

SMART/LEARN BUTTON

2

3

1

KG

KG

4

Motor Unit

Select a button to program.
Press button times

ensuring LED stops flashing

after each press. Code is

accepted when door

activates.

REMOTE CONTROL BATTERY

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Dispose of batteries properly. Replace ONLY with 3V2032 coin
batteries.

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.

Do NOT recharge, disassemble, heat above 212°F (100°C) or
incinerate.

CHART B

# of

Brand

Description

Year

times to
press
button

11 Chamberlain

®

* 9

Position ’90-’92

12 Chamberlain

®

* 9

Position

Canada

’83-’89

13 Genie

®

12

Position

’85

14 Linear

Multicode

®

10

Position ’76

15 Chamberlain

®

8

Position

’83-’89

16 Stanley/Multicode

®

10

Position

’76

17 Genie

®

9

Position

’85

18 Linear

®

Moore-O-Matic

®

8

Position ’76

19 Chamberlain

®

* 7

Position ’83-’89

CHART A

# of

Brand

Type/Color of Year

times to

Smart/Learn

press
button

1 Linear

®

Mega-Code

’97-Current

2 Chamberlain

®

* Orange

’97-’05

3 Chamberlain

®

* Purple

’05-Current

4 Chamberlain

®

* Green

’93-’96

5 Genie

®

Overhead

Door

®

Intellicode

’95-Current

6 Genie

®

Overhead

Door

®

Intellicode

’05-Current

7 Stanley

®

Secure

Code

’98

9 Wayne

Dalton

®

Rolling

Code ’99

11 Chamberlain

®

* 9

Position

’90-’92

1-800-442-1255

Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie
is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead
Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a
Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark
of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is
a trademark of Do It Best Corporation.

Press program button.

6

7

Programming complete.
Press selected button
to test. If unit does not
work, return to Step 3.

Press and release the
smart/learn button.

5

Select a button to program.
Press button times
ensuring LED stops flashing
after each press. Code is
accepted when one of the
following occurs:

OR

OR

1

See Chart B to
determine # of times to
press button and write
in blank on step 5.

DIP SWITCH

SMART/LEARN BUTTON

Press program button.

6

7

Programming complete.
Press selected button
to test. If unit does not
work, return to Step 3.

3

Press program button
until LED lights.

2

1

See Chart A to
determine # of times to
press button and write
in blank on step 5.

NOTE: Your opener may
appear different and you
may have to remove the
light lens to access the
learn button.

*NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible
with Chamberlain technology.

Click

www.LiftMaster.com

12

11

10

9

8

5

3

7

6

4

1

2

LED Indicator

Button 1

Button 2

Program Button

Battery

DIP Switches

Battery Cover

Motor
Unit

ON

STOP

Advertising