End of cycle signal, Changing cycles, modifiers, and options, Drying rack option – Whirlpool Cabrio W10151493B Manuel d'utilisation

Page 21

Advertising
background image

21

End of Cycle Signal

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end

of the cycle reduces wrinkling.
Press END OF CYCLE SIGNAL until the desired volume (Loud,

Soft, or Off) is selected.

NOTE: When the WRINKLE SHIELD™ setting is selected and the

End of Cycle Signal is on, a tone sounds every 5 minutes until the

clothes are removed, or the WRINKLE SHIELD™ setting ends.

Changing Cycles, Modifiers,

and Options

You can change Automatic and Timed Cycles, Modifiers, and

Options anytime before pressing Start.

Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice.
2. Select the desired cycle and options.
3. Press START. The dryer starts at the beginning of the new

cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

Changing Modifiers and Options after pressing Start

You can change an Option or Modifier anytime before the

selected Option or Modifier begins.
1. Press PAUSE/CANCEL once.
2. Select the new Option and/or Modifiers.
3. Press START to continue the cycle.
NOTE: If you happen to press PAUSE/CANCEL twice, the

program clears and your dryer shuts down. Restart the selection

process.

Changing the Preset Dryness Level Settings

If Auto Dry cycle loads are not as consistently dry as you

would like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all

of your Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different

installations, environmental conditions, or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time),

and 3 (much dryer clothes, approximately 30% more drying

time).
1. The Dryness Level settings cannot be changed while the

dryer is running.

2. Press and hold the DRYNESS button for 5 seconds. The

dryer will beep, and “CF” will be displayed for 1 second

followed by the current drying setting.

3. To select a new drying setting, press the DRYNESS button

again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting

will not flash, but the other settings will flash.

4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.

Drying Rack Option

Use the Drying Rack to dry items such as sweaters and pillows

without tumbling. The drum turns, but the rack does not move.
If your model does not have a drying rack, you may be able to

purchase one for your model. To find out whether your model

allows drying rack usage and for information on ordering, please

refer to the front page of the manual or contact the dealer from

whom you purchased your dryer.
NOTE: The rack must be removed for normal tumbling. Do not

use the automatic cycle with the drying rack.
To use the drying rack
1.
Open dryer door.

2. Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on

front edge of drying rack to secure at the front of the dryer.

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.
5. Press the POWER button.
6. Select a timed drying cycle and temperature (see following

chart). Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only temperature setting.

A. Front edge

A. Dryer rack front edge
B. Dryer back panel

A

A

B

Advertising
Ce manuel est liée aux produits suivants: