Whirlpool WGD9750WW - Manuel (Page 8)

8
■ The Wrinkle Shield Steam feature is not available on Delicate
or Super Delicate Automatic Cycles and Timed Cycles with
Low, Extra Low, and Air Only Temperature selected. WRINKLE
SHIELD™ without Steam cycle is available for these cycles.
■ For the Casual Cycle, the WRINKLE SHIELD™ STEAM feature
is preset to “ON.” The other cycles will retain the WRINKLE
SHIELD™ STEAM feature setting.
Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished.
Press until the desired volume (Loud, Soft, or Off) glows green.
NOTE: When the WRINKLE SHIELD™ STEAM feature is selected
and the End of Cycle Signal is on, an audible sound will be
emitted every 5 minutes until the clothes are removed, or the
WRINKLE SHIELD™ STEAM feature is finished.
Button Sound
You can change the volume of the sound of the beeps. Press until
the desired volume (Loud, Soft, or Off) glows green. The Power
and Cancel buttons will still beep softly even when the Button
Sound volume is set to Off.
Drum Light and Controls Lock/Unlock
Drum Light
When pressed during a cycle, the Drum Light turns on and will
remain on until pressed again, the door is opened and closed, or
the door is left open for 20 minutes.
Controls Lock/Unlock
To enable the Controls Lock feature when dryer is running:
Press and hold the CONTROLS LOCK/UNLOCK button for
3 seconds. The control is locked when a single beep is heard and
the Controls Lock status light is on. This feature allows you to lock
your settings to avoid unintended use of the dryer. You can also
use the Controls Lock feature to avoid unintended cycle or option
changes during dryer operation.
■ When the dryer is off, it is not necessary to press the Control
On button before activating the Controls Lock feature.
To unlock:
Press and hold the CONTROLS LOCK/UNLOCK button for
3 seconds to turn this feature off.
NOTE: When the dryer is running and Controls Lock is on, the
dryer can be stopped by pressing the Pause/Cancel button, but
cannot be restarted until the control is unlocked.
Changing Cycles, Options, and Modifiers
You can change Auto Cycles, Timed Cycles, Options, and
Modifier, and anytime before pressing Start.
■ Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press PAUSE/CANCEL twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of the
new cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
Changing Options and Modifiers after pressing Start
You can change an Option or Modifier anytime before the selected
Option or Modifier begins.
1. Press PAUSE/CANCEL once.
2. Select the new Option and/or Modifier.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Pause/Cancel twice, the program
clears and your dryer shuts down. Restart the selection process.
Changing the Preset Dryness Level Settings
If all your loads on all Auto Dry cycles are consistently not as dry
as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly drier clothes, approximately 15% more drying time),
and 3 (much drier clothes, approximately 30% more drying time).
1. The Dryness Level settings cannot be changed while the dryer
is running.
2. Press and hold the Dryness Level button for 5 seconds. The
dryer will beep, and “CF” will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the Dryness Level key
again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.