Whirlpool 24" (58 CM) - Manuel (Page 8)

8
2. To wire through top:
Mark a line 7½" (19.0 cm) from the right of the centerline on
the underside of the cabinet. Mark the point on this line that is
2" (5.0 cm) from back wall. Drill a 1¼" (3.0 cm) diameter hole
through the cabinet at this point.
To wire through rear wall:
Mark a line 7½" (19.0 cm) from the right of the centerline on
the wall. Mark the point on this line that is ¾" (1.9 cm) from
underside of cabinet. Drill a 1¼" (3.0 cm) diameter hole
through wall at this point.
Style 1 - Cut Openings for 3¼" x 10" (8.3 cm x 25.4 cm)
Rectangular Vent System
Roof Venting
To make a 4" x 10½" (10.2 cm x 26.7 cm) rectangular cutout
on the underside of cabinet top and bottom:
1. Mark lines 1½" (3.8 cm) and 5½" (14 cm) from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for
vent.
4. Repeat steps 1-3 for the underside of the top of the cabinet
Wall Venting
To make a 4" x 10½" (10.2 cm x 26.7 cm) rectangle in the wall:
1. Make 2 lines by measuring from floor 65 ⁷⁄₈" (167.3 cm) and
62
³⁄₈" (158.4 cm) or ¹⁄₈" (3.2 mm) and 3⁵⁄₈" (9.2 cm) down from
underside of cabinet and mark on the centerline on the back
wall.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the wall.
3. Use saber or keyhole saw to cut a rectangular opening in the
wall for the vent.
Style 2 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm)
Rectangular Vent to 6" (15.2 cm) Round Vent Transition
Roof Venting
To make a 4" x 10½" (10.2 x 26.7 cm) rectangular cutout on the
underside of cabinet bottom:
1. Mark lines 1½" (3.8 cm) and 5½" (14 cm) from the back wall
on the centerline of the underside of cabinet.
2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline
on the underside of cabinet.
3. Use saber or keyhole saw to cut a rectangular opening for
vent.
To make a 6 ¹⁄₄" (15.9 cm) circle on the underside of the cabinet
top:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line 4 ³⁄₄" (12.1 cm) from the back wall on the underside
of the top of cabinet.
3. Draw a circle using a compass or 6 ¹⁄₄" (15.9 cm) circle
template.
Centerline
2" (5.1 cm)
from wall,
not cabinet
frame
7 ¹⁄₂ "
(19 cm)
7 ¹⁄₂ "
(19 cm)
Centerline
³⁄₄ " (1.9 cm)
5 ¹ / ₄ "
(13.3 cm)
5 ¹ / ₄ "
(13.3 cm)
*5 ¹ / ₂ "
(14 cm)
*From wall, not cabinet frame
Cabinet cutouts
*1 ¹ / ₂ " (3.8 cm)
¹⁄₈ "
3 ⁵⁄₈ "
Cabinet
front
5 ¹⁄₄ "
(3.2 mm)
(9.2 cm) (13.3 cm)
Centerline
5 ¹ / ₄ "
(13.3 cm)
5 ¹ / ₄ "
(13.3 cm)
*5 ¹ / ₂ "
(14 cm)
*From wall, not cabinet frame
*1 ¹ / ₂ " (3.8 cm)