Status lights, Cycles – Whirlpool Cabrio W10164159A Manuel d'utilisation

Page 21

Advertising
background image

21

Drying tips

Follow care label directions when they are available.

If desired, add a fabric softener sheet. Follow package
instructions.

To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits and synthetic fabrics.

Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.

Cycle tips

Dry most loads using the preset cycle settings.

Refer to the Automatic or Timed Preset Cycle Settings chart
(in the “Cycles” section) for a guide to drying various loads.

Drying temperature and dryness level are preset when
you choose an Automatic Cycle. You can select a
different dryness level, depending on your load, by
pressing Dryness and choosing More, Normal, Less or
Damp.

NOTE: You cannot use the Time Adjust and you cannot
choose a Temperature with the Automatic Cycles.

If you wish to adjust the cycle length of a Timed Cycle,
press the Time Adjust up or down arrows. Adjust the
temperature of a Timed Cycle by pressing Temp until the
desired temperature is selected.

NOTE: You cannot choose a dryness level with Timed
Cycles.

Status Lights

Follow the progress of your dryer with the drying Status indicator
lights.

Sensing

In an Automatic Cycle, the Sensing light illuminates until a
wet item is detected.

In the Timed Cycle, the Sensing light illuminates at the
beginning of a cycle and turns off 5 minutes into the cycle.

Wet

The Wet light illuminates at the beginning of an Automatic Cycle if
a wet item is detected.

In an Automatic Cycle, if a wet item is not detected after
approximately 5 minutes, the dryer goes directly into Cool
Down and the Cool Down and the WRINKLE SHIELD™
setting indicators illuminate, if selected.

In a Timed Cycle, wet items are not detected. The dryer will
continue to run for the length of time selected, and the Wet
light will illuminate. The damp light will not illuminate.

In the Enhanced Touch Up or the Quick Refresh Steam
Cycles, the Wet light comes on after the water has been
sprayed into the drum, 5-6 minutes into the cycle. The Wet
light illuminates until the dryer goes into Cool Down with
1 minute of time remaining.

Damp

The Damp light illuminates in an Automatic Cycle when the
laundry is approximately 80% dry. Damp Dry Signal beeps, if
selected. See “Options.”

Cool Down

The Cool Down light illuminates during the cool down part of the
cycle. Laundry cools for ease in handling.

Done

The Done light illuminates when the drying cycle is finished. This
indicator stays on during the WRINKLE SHIELD™ setting.

WRINKLE SHIELD™ Setting

The WRINKLE SHIELD™ setting light illuminates when this
option is selected. This indicator stays on during the WRINKLE
SHIELD™ setting.

Indicator lights

Other indicator lights show Cycle, Modifiers, Options and Cycle
Signal settings selected. The display shows the estimated or
actual time remaining.

Cycles

Select the drying cycle that matches the type of load you are
drying. See the Automatic, Steam or Timed Preset Cycle Settings
Charts.

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you
are drying. See the following Automatic Preset Cycle Settings
chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and
automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get high heat for heavyweight mixed loads,
cottons and jeans.

Normal

Use this cycle to get medium heat for drying sturdy fabrics such
as work clothes.

Casual

Use this cycle to get low heat for drying no-iron fabrics, such as
sport shirts, casual business clothes and permanent press
blends.

Delicate

Use this cycle to get extra-low heat to gently dry items such as
lingerie, blouses or washable knit fabrics.

Advertising