Programming without a code – Panasonic CT-32HC15 Manuel d'utilisation

Page 46

Advertising
background image

R

EMOTE

C

ONTROL

O

PERATION

/ O

PERACIÓN DEL

C

ONTROL

R

EMOTO

/ F

ONCTIONNEMENT DE LA TÉLÉCOMMANDE

Re

mot

e

Re

m

o

to

Télécomma

nde

Programming The Remote Control
Programación del Control Remoto
Programmation de la télécommande

The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, CABLE or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
El Control Remoto Universal puede programarse para
operar componentes de varios fabricantes usando los
botones de función para VCR, DVD, CABLE o DBS.
Siga los procedimientos para programar su Control
Remoto con o sin código para el componente.
La télécommande universelle peut être programmée pour
commander le fonctionnement d'appareils d'autres
marques à l'aide des touches de fonctions VCR, DVD,
CABLE, ou DBS. Suivre l'une des procédures de
programmation données ci-dessous.

Note:

Determine the manufacturer of the component and look in the
table for the code.

Nota:

Determine el fabricante del componente y busque en la
tabla su código.

Nota:

Noter la marque de l'appareil et identifier le code dans le
tableau des codes.

English Procedures

1.

Confirm that the external component is plugged in and
operating.

2.

Turn the component off.

3.

Press and

together,

for at least 5

seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.

4.

Press appropriate component button on the Remote
Control: VCR, DVD, CABLE or DBS. The component
button will illuminate steadily and all others will go out.

5.

Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.

6.

Press the Remote Control

to test the

component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.

Note:

If the component does not operate with the Remote Control,
repeat steps 3 through 6 using another code (some brands
have multiple codes). If an incorrect code is entered, or if the
procedure takes longer than 30 seconds, the programming will
fail.

Programming Without A Code

This procedure searches all codes and is called the
“sequence method.”

1.

Confirm that the external component is plugged in and
on.

2.

Turn the component off.

3.

Press and

together,

for at least 5

seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.

4.

Press the appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.

5.

Press the

button to set the remote control into

the step mode.

6.

Point the remote control towards the component.

7.

Press VOL

X (the mode key will blink three times), then

press the Remote Control

button to test the

component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.

Note:

Each time you press the VOL

X button, make sure that the

component key blinks twice before pressing the POWER
button.

8.

Once the device responds, press

to store the

code. The mode (component) button will blink twice.

Note:

It may take many attempts before the correct code is found. If

you miss a code, press

W VOL, then press the

button to test the component.

Procedimiento Español

1.

Confirme que el componente esté conectado y en
operación.

2.

Apague el componente.

3.

Presione los botones de

y

juntos,

cuando menos 5 segundos. Después de este tiempo,
los botones de componentes comenzarán a destellar.
Desoprima los botones ACTION y POWER.

4.

Presione el botón de la función apropiada del
componente en el Control Remoto. (VCR, DVD, CABLE
o DBS). El botón seleccionado quedará iluminado y el
resto se apagará.

5.

Accese el código del componente de 3 dígitos usando el
teclado numérico (botones 0 ~ 9) del Control Remoto. El
botón del componente destellará dos veces.

6.

Presione el botón

de el Control Remoto para

probar el componente. Si éste procedimiento ha sido
exitoso, el componente se encenderá.

Device
Equipo
Appareil

Operates

Funciona

Contrôle

Default

Réglage par défaut

TV
Televisión
Téléviseur

Panasonic Only

Solo Panasonic

Panasonic seulement

Panasonic Code

Código TV Panasonic

Codes Panasonic

VCR

Videocasetera
Magnétoscope

VCR (Preset)

Videocasetera

(predefinido)

Magnétoscope (

Préréglé

)

Panasonic Code

Código Panasonic

Codes Panasonic

DBS/CBL

DBS STB & CBL STB

(Preset/predefinido Préréglé)

Panasonic DBS Code

Código Panasonic DBS

Codes DBS Panasonic

DVD
Lecteur DVD

DVD (Preset)

DVD/disco Compacto

(predefinido)

Lecteur DVD et CD (Préréglé)

Panasonic Code

Código Panasonic

Codes Panasonic

ACTION

POWER

POWER

ACTION

POWER

POWER

POWER

ACTION

POWER

ACTION

POWER

POWER

Advertising