Panasonic AJ-B95 - Manuel (Page 74)

74
V1 V2
CONTROL
EJECT
VTR 1
AUDIO MONITOR SELECT
L R
CH 1
4
1
3
MIX
ANALOG
MIX
2
UNI
V2
PB
SDI REC
VAR
CH 2 CH 3 CH 4
CH 3 4
VTR 2
M-cassette
Caution Do not Insert S-cassette or with adaptor
<
EJECT
<
REMOTE
LOCAL
EXT VTR
PREROLL SYNCHRO
CTL
UB
TC
7 5
3
CF
ON OFF
REGEN
R-RUN
F-RUN
MODE REC INHIBIT TC
VTR 1
TAPE
EE
ON
OFF
REGEN
R-RUN
F-RUN
MODE REC INHIBIT TC
VTR 2
TAPE
EE
ON
OFF
ANALOG OPERATION MODE EDIT
V2 VIDEO IN
SDI
ANALOG SEPARATE
EXT
AUDIO IN
V1-V2
V1
V2
OUT 2 CH
4 CH
2 CH
4 CH
CTL
UB
TC
M-cassette
Caution Do not Insert S-cassette or with adaptor
4
(V1·2) V1 V2
1
3
MIX
MIX 2
4
1
3
MIX
MIX
ASMBL V A1 A2
1ST EDIT
PREVIEW
VTR 2 VTR 1 SPLIT
MARK OUT MARK IN
SHIFT ENTER ALL STOP
REVIEW
AUTO EDIT
MULTI
GO TO
GO TO OUT
DUR
TOTAL
OUT
LAST ED
IN
LAST X
EVENT
7 8 9
4 5 6
1 2
0 C
3
~
-
+
DELETE
SET UP F/TC DIAG
LIST CORCT BS TRACK
DUMP LOAD FS
DISP EXIT RETURN
T SET
PLAY
STOP
STILL REW FF
STB OFF
A3 A4
TC REC EDIT
2
4
1
3
MIX
MIX
2
4
1
3
MIX
MIX
2
4
1
3
MIX
MIX
2
SDI
CH 1 CH 2
V2 / V1 PB REC
CH 3 CH 4
INT
ANALOG SDI
10
10
20
30
00
INT
INT
ANALOG SDI INT
ANALOG SDI
V2 INPUT
INT
0
10
10
20
30
00
0
10
10
20
30
00
0
CH 1
POWER
OFF ON
UNI
VAR
CH 2 CH 3 CH 4
ANALOG V1/V2
REC
INT
ENTER
T SET
([SHIFT] + [3])
Setting the time code (T SET)
TC generator switch
When recording manually by setting the
initial value of the time code
This procedure is followed to set the initial value of the
time code for manual recording or 1ST EDIT.
1
Set the TC generator switch of the VTR which is to
be used for recording to R-RUN (REC RUN) or F-
RUN (FREE RUN).
In the REC RUN mode, the time code advances
only while recording is in progress.
In the FREE RUN mode, the time code advances
as soon as the time code setting is completed (and
it advances all the time while the power is kept on).
2
Press the T SET ([SHIFT] + [3]) button.
3
Use the numeric input buttons to input the initial
value of the time code to be recorded.
4
Press the ENTER button.
5
When recording manually by presetting the user’s
bit as well, perform the following settings 1
through 4.
1 Align the cursor with setup menu item No.574
(UB PRESET).
2 Press the T SET ([SHIFT] + [3]) button.
3 Use the numeric input buttons to input the
desired user’s bit value. (See page 75)
4 Press the ENTER button.
<Note>
When recording manually, the initial value of the time
code can be set by setting the TC generator switch to
R-RUN or F-RUN regardless of what is selected as
the setup menu item No.504 (REGEN MODE) setting.
6
Select the VTR to be used for recording, and press
the REC button and PLAY button to start the
recording.