69 special features, Large screen correction, English – Panasonic PT DW10000U Manuel d'utilisation

Page 69: After all the data has been input, press menu

Advertising
background image

ENGLISH –

69

Special Features

6. Use the colorimeter to

measure the luminance (Y) and
chromaticity coordinates (x, y).

7. Press

▲▼ to select the colors,

and press

◄► to select their

values.

8. After all the data has been input,

press MENU.

The “MEASURE MODE” screen will be
displayed.

Inputting the coordinates of a
desired color

9. Press

▲▼ to select “MODE”.

10. Press

▲▼ to select “7COLORS”.

11. Press

▲▼ to select “TARGET

DATA”.

12. Press ENTER.

The “TARGET DATA” screen will be displayed.

13. Press

▲▼ to select “R, G, B” or

“Cy, Mg, Ye, Wh”.

14. Press ENTER.

The “TARGET DATA: R, G, B (or “Cy, Mg, Ye,
Wh”)” screen will be displayed.

15. Press

▲▼ to select the desired

colors, and press

◄► to input

their coordinates.

ENTER

MEASURE MODE

MODE
MEASURED DATA

TARGET DATA

AUTO TESTPATTERN

MENU SELECT

SUB MENU

709MODE

ON

ENTER

MEASURE MODE

MODE
MEASURED DATA

TARGET DATA

AUTO TESTPATTERN

MENU SELECT

SUB MENU

709MODE

ON

ENTER

TARGET DATA
TARGET DATA:R,G,B

TARGET DATA:Cy,Mg,Ye,Wh

MENU SELECT

SUB MENU

ENTER

TARGET DATA
TARGET DATA:R,G,B

TARGET DATA:Cy,Mg,Ye,Wh

MENU SELECT

SUB MENU

TARGET DATA: R, G ,B
R

G

B

MENU SELECT
ADJUST

x

y
x
y
x
y

0.670
0.330
0.650
0.630
0.150
0.050

TARGET DATA: R, G ,B
R

G

B

MENU SELECT
ADJUST

x

y
x
y
x
y

0.670
0.330
0.650
0.630
0.150
0.050

16. After all the data has been input,

press MENU.

Note

If “3COLORS” or “709MODE” has been selected as
the “TARGET MODE” setting, only the 3 colors R, G
and B will be input for “TARGET DATA”.

If “709MODE” has been selected as the “TARGET
MODE” setting, the 3 primary colors defined by the
ITU-R BT.709 standard will be set as the target
data.

If the target data is outside the color range of the
projector, the colors will not be projected correctly.

Large Screen Correction

If watching images close up on a large screen, you
can correct the colors that appear lighter on the
screen so that they appear the same as the colors
that would appear on a normal-sized screen.

1. Press

▲▼ to select “LARGE

SCREEN CORRECTION”.

2. Press

◄► to switch “LARGE

SCREEN CORRECTION”.

The setting will change as follows each time
◄► is pressed.

OFF (No correction)

1 (Low)

2 (High)

OPTION1

COLOR MATCHING

LARGE SCREEN CORRECTION

AUTO SIGNAL
AUTO SETUP
BACK COLOR
DVI EDID
AUX DVI EDID
P IN P
FUNC1
OSD POSITION
OSD MEMORY

MENU SELECT

CHANGE

OFF
OFF
OFF

BLUE

EDID2(PC)
EDID2(PC)

OFF

P IN P

2

ON

OPTION1

COLOR MATCHING

LARGE SCREEN CORRECTION

AUTO SIGNAL
AUTO SETUP
BACK COLOR
DVI EDID
AUX DVI EDID
P IN P
FUNC1
OSD POSITION
OSD MEMORY

MENU SELECT

CHANGE

OFF
OFF
OFF

BLUE

EDID2(PC)
EDID2(PC)

OFF

P IN P

2

ON

Advertising