Panasonic PT DW10000U - Manuel (Page 57)

ENGLISH – 57
Basic Operation
Adjusting the aspect ratio
This changes the aspect ratio of the pictures.
1. Press
▲▼ to select “ASPECT”.
2. Press ◄► to switch “ASPECT”.
The setting will change as follows each time
◄► is pressed.
DEFAULT:
Pictures are displayed without changing the aspect
ratio of the input signals.
THROUGH:
Pictures are displayed without changing the
resolution of the input signals.
16:9 *1 :
When standard signals are being input *3 , pictures
are displayed with the aspect ratio converted to
16:9. When wide-screen signals are being input
*4 ,
pictures are displayed with the aspect ration of the
input signals unchanged.
4:3 *2 :
When standard signals are being input *3 , pictures
are displayed with the aspect ration of the input
signals unchanged. When wide-screen signals
are being input
*4 , the PT-D10000U displays the
pictures with the aspect ratio converted to 4:3. The
PT-DW10000U displays the pictures with the aspect
ratio unchanged, but reduces the size of the pictures
so that they fit within the 4:3 projection area.
•
•
•
•
•
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
KEYSTONE
MENU SELECT
CHANGE
DEFAULT
0
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
KEYSTONE
MENU SELECT
CHANGE
DEFAULT
0
VID AUTO (PRIORITY)
*1: PT-D10000U Only
*2: PT-DW10000U Only
S1 AUTO
VID AUTO
HV FIT
H FIT* 2
DEFAULT
THROUGH
16:9* 1
4:3* 2
S4:3* 1
VID AUTO (PRIORITY)
*1: PT-D10000U Only
*2: PT-DW10000U Only
S1 AUTO
VID AUTO
HV FIT
H FIT* 2
DEFAULT
THROUGH
16:9* 1
4:3* 2
S4:3* 1
S4:3 *1 :
Select when using a 16:9 screen.
H FIT *2 :
Pictures are displayed using all the panel pixels in
the horizontal direction. Signals with an aspect ratio
where the pictures are taller than with a ratio of 16:9
will be displayed with their bottom areas cut off.
HV FIT:
Pictures are displayed on the whole panel pixels.
If the aspect ratio of the input signals is different
from that of the panel, the pictures are displayed
by converting it into the panels aspect ratio (4:3 for
PT-D10000U and 16:9 for PT-DW10000U).
VID AUTO:
The projector identifies the video ID (VID)
embedded in the picture signals and displays the
picture by automatically switching the screen sizes
between 4:3 and 16:9. This function is effective for
the NTSC signal input.
S1 AUTO:
The projector identifies the S1 signal and displays
the picture by automatically switching the screen
sizes between 4:3 and 16:9. This function is
effective for S-Video NTSC signals.
VID AUTO (PRIORITY):
The projector identifies the abovementioned VID or
S1 signals and displays the picture by automatically
choosing the screen sizes of 4:3 or 16:9 according
to the VID if it is detected or S1 signals if a VID is
not detected. This function is effective for S-Video
NTSC signals.
*3: Standard signals are input signals with an aspect
ratio of 4:3 or 5:4.
*4: Wide-screen signals are input signals with an
aspect ratio of 16:9, 15:9 or 15:10.
Note
Some size modes are not available for certain types
of input signals. For NTSC signals, “DEFAULT”
cannot be selected.
If an aspect ratio which is different from the aspect
ratio for the input signals is selected, the pictures
will appear differently from the originals. Be careful
of this when selecting the aspect ratio.
If using this projector in places such as cafes or
hotels to display programmes for a commercial
purpose or for public presentation, note that
adjusting the aspect ratio or using the zoom
function to change the screen pictures may be an
infringement of the rights of the original copyright
owner for that programme under copyright
protection laws.
If conventional (normal) 4:3 pictures which are
not wide-screen pictures are displayed on a wide
screen, the edges of the pictures may not be visible
or they may become distorted. Such pictures
should be viewed as with an aspect ratio of 4:3 in
the original format intended by the creator of the
pictures.
•
•
•
•
•
•
•
•
•
•