Power and sound controls, Clock setting, Audio mode (bass/treble/balance/fader/sub woofer) – Panasonic CQ-C1200U Manuel d'utilisation

Page 7: Initial time, Time reset, Mute, Volume, Sq (sound quality), Power, Display change

Advertising
background image

POWER

CLOCK

CQ-C1200U

DI

SP

SQ

MUTE

7

8

9

10

11

12

SCAN

1

2

3

4

6

APM

BA

N

D

SRC

5

VOL

UME / PUSH SE

L

REP

TUNE

TRACK

D

M

POWER

CLOCK

CQ-C1200U

DI

SP

SQ

MUTE

7

8

9

10

11

12

SCAN

1

2

3

4

6

APM

BA

N

D

SRC

5

VOL

UME / PUSH SEL

REP

TUNE

TRACK

D

M

1

E
N

G

L

I

S
H

13

CQ-C1200U/C1120U/C1110U/C1100U

1

E
N

G

L

I

S
H

2

12

CQ-C1200U/C1120U/C1110U/C1100U

Hours

w

Press and hold [DISP] (clock) for more than 2
seconds.

e

Press [k TUNE] or [l TUNE].

Minutes

r

Press [DISP] (clock).

t

Press [k TUNE] or [l TUNE].

y

Press [DISP] (clock).

Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.

Audio Mode
(Bass/Treble/Balance/Fader/Sub Woofer)

Regular mode

Volume

Bass

Treble

Balance

Sub Woofer

Fader

Note: If no operation takes place for more than 5 sec-
onds in audio mode (2 seconds in volume mode), the
display returns to the regular mode.

Bass:

Adjustable range: –12 to +12 (by 2 dB step)

Treble:

Adjustable range: –12 to +12 (by 2 dB step)

Balance:

R (right speaker) or L (left speaker)

Fader:

F (front speaker) or R (rear speaker)

Push [SEL] to select the audio mode.

q

Clock Setting

The 12-hour system is used for the clock.

(Hours blink.)

(Hours set.)

(Minutes blink.)

(Minutes set.)

(End.)

Initial Time

q

Press [DISP] (clock).

"AdJ" is displayed when the clock is not
adjusted.

Time Reset

Press and hold [DISP] (clock) for more than
2 seconds to activate the time setting mode to
reset the time. Then, repeat steps e to y.

[DISP] (clock)

[k TUNE], [l TUNE] (Hours, minutes)

Adjustable range: 1 to 15 (by 1 step) Balance center

Adjustable range: 1 to 15 (by 1 step)

Fader center

(Only for CQ-C1200U)

Sub Woofer:

Adjustable range (level): MUTE (0) to 7

(Only for CQ-C1200U)

Push

Turn [VOLUME] clockwise or counterclockwise
to change each level.

w

default: 0 dB

default: 0 dB

(default)

(default)

default: 4

D

IS

P

SQ

MUTE

SRC

Power and Sound Controls

Mute

Press [MUTE] to mute the sound completely.

lights

Press [MUTE] again to cancel.

Volume

Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.

Volume level (0 to 40)

(default: 18)

SQ (Sound Quality)

SQ is a function that can call up various sound types at
the touch of button in accordance with your listening
music type.

Press [SQ] to select a sound type as follows:

(default)

SQ -- (default)

flat frequency response:
does not emphasize.

SQ - 1 (ROCK)

speedy and heavy sound:
exaggerates bass and treble.

SQ - 2 (POP)

wide-ranged and deep sound:
slightly emphasizes bass and treble.

SQ - 3 (VOCAL)

clear sound:
emphasizes middle tone and
slightly emphasizes treble.

Power

Turn the key in the ignition until
the accessory indicator lights.
Power on: Press [SRC] (POWER).
Power off:
Press [SRC](POWER)

again and hold.

ACC

ON

MUTE

ST

Display Change

Press [DISP] (display) to switch to the clock display.

Note: "AdJ" is displayed when the clock is not adjusted.
(

page 13)

When the power is off:

No display

Clock display

Remote control sensor (

page 18)*

(only for CQ-C1200U/C1120U/C1110U)

Up

Down

SQ indicator

Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.

Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio signal,

readjust bass/treble or volume (

page 13)

.

• CQ-C1100U has no remote control function.*

Advertising
Ce manuel est liée aux produits suivants: