Pioneer Car Stereo Receiver DEH-P5200 Manuel d'utilisation

Inst alla tion manual manuel d’inst alla tion, Deh-p5200, Connecting the units <english

Advertising
background image

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

<99K00F0P01>

DEH-P5200

Printed in Thailand

Imprimé en Thaïlande

<CRD3154-A/N> UC

Connecting the Units

<ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning
installation.

• Refer to the owner’s manual for details on

connecting the power amp and other units, then
make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.

• Speakers connected to this unit must be high-

power types with minimum rating of 45 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.

• If the RCA pin jack on the unit will not be used, do

not remove the caps attached to the end of the con-
nector.

• When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.
Connect to an external power amp’s system remote
control or the car’s Auto-antenna relay control ter-
minal (max. 300 mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster
power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do not
connect the blue/white lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insulat-
ed.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same
colors correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehi-
cle for several hours. (Fig.1)

Fig. 1

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.

No ACC position

ACC position

ON

S

T

A

R

T

O

FF

ACC

ON

S

T

A

R

T

O

FF

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.

• Cords for this product and those for other products

may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.

Advertising