How to use on screen menu, Video config system config – Panasonic BT-LH1500P Manuel d'utilisation

Page 7

Advertising
background image

7

[VIDEO CONFIG]

>COLOR TEMP D65

SHARPNESS H 3

SHARPNESS V 3

I-P MODE MODE2

MONO OFF

SD ASPECT 4:3

HD ZOOM NORMAL

VIDEO CONFIG menu

VIDEO CONFIG

SYSTEM CONFIG

With SYSTEM CONFIG selected, the following menu will
appear.

BACKLIGHT
Used to adjust the brightness of backlight.
Set-value (underlined is default value)

0 – 63

(BT-LH1800)

0 – 32 – 63 (BT-LH1500)

POSITION
Used to set the display position of on screen menu.
Set-value (underlined is default value)

CENTER (center of screen), LT (top left of screen),
RT (top right of screen),

RB (bottom right of screen),

LB (bottom left of screen).

ERROR MESSAGE
Used to select whether or not displaying transmitting system
error of SDI and HD-SDI. If an error is generated, “CRCC
ERROR” will be displayed.
Set-value (underlined is default value)

ON

OFF

STATUS DISPLAY
Used to set the information display in case of input change
or the format display in case of signal input.
Set-value (underlined is default value)

CONTINUE

3SEC OFF

OFF

CONTROL LOCK
All menu items other than CONTROL LOCK and front panel operations
other than power switch are locked (invalidated). Even when locked, it
returns to preset value with picture adjusting knob pushed in.
Set-value (underlined is default value)

ON

OFF

SETUP
• LOAD
Used to read in the set-value being saved.
“FACTORY” reads in the factory-adjusted value.
Set-value (underlined is default value)

FACTORY

USER1*

1)

USER2*

1)

USER3*

1)

USER4*

1)

USER5*

1)

• SAVE
Current set-values can be saved up to 5.
Set-value (underlined is default value)

USER1

USER2

USER3

USER4

USER5

*

1)

The contents of USER1 – USER5 and FACTORY are same at

the time of delivery from the factory.

[SYSTEM CONFIG]

>BACKLIGHT 63

POSITION CENTER

ERROR MESSAGE ON

STATUS DISPLAY CONTINUE

CONTROL LOCK OFF

[SET UP]

LOAD FACTORY

SAVE USER1

SYSTEM CONFIG menu

How To Use On Screen Menu

With VIDEO CONFIG selected, the following menu will appear.

COLOR TEMP
Used to set the color temperature
Set-value (underlined is default value)

USER 0 – 63*

1)

D93

D65

SHARPNESS H
Used to set the sharpness in horizontal direction.
Set-value (underlined is default value)

0 –15*

2)

Default value

3 (HD)

12 (SD)

(BT-LH1800)

2 (HD)

2 (SD)

(BT-LH1500)

SHARPNESS V
Used to set the sharpness setting in vertical direction.
Set-value (underlined is default value)

0 –15*

2)

Default value

3 (HD)

3 (SD)

(BT-LH1800)

2 (HD)

2 (SD)

(BT-LH1500)

I-P MODE
Used to set the mode for IP change.
Set-value (underlined is default value)

MODE1

MODE2

MONO
Used to make setting for mono-chrome display.
Set-value (underlined is default value)

ON

OFF

SD ASPECT
Used to set the aspect ratio in case of SD signal input.
Select REMOTE when executing external change by REMOTE terminal.
Set-value (underlined is default value)

REMOTE 16:9

4:3

HD ZOOM
Enlarged 4:3 is displayed by PAN&SCAN in case of 1080I,
1035I, 720P signal input.
Select REMOTE when executing external change by REMOTE
terminal.
This item is displayed only when HD SDI input unit or compo-
nent/RGB input unit is installed.
Set-value (underlined is default value)

4:3

NORMAL

REMOTE

*

1)

By user setting, it is possible to change the color temperature in

64 stages from 0 (around 3000K) to 63 (around 9300K).

*

2)

Sharpness value has a set-value and is displayed for each of in-

put signal (HD/SD)

Advertising
Ce manuel est liée aux produits suivants: