KITCHENAID KBGS292LSS - Manuel (Page 8)

8
IMPORTANT: Light only one burner at a
time.
1. Do not lean over burners. Push in and
turn to "LITE" the control knob for the
burner you wish to use.
2. Push in the burner ignitor button. You
will hear the “snapping” sound of the
spark. Keep the burner ignitor button
pushed in until burner lights. Make sure
burner is lit. Repeat for each of the
other burners as needed.
IMPORTANT:
If burner does not light immediately, turn the
burner knob to “OFF” and wait 5 minutes
before relighting.
infrared
burner
control
knob
smoker
tray
smoker tray
burner
control knob
grill burner
control knob
grill burner
control knob ignitor battery
compartment
red button
burner
igniter
button
Grill Use
Using your Grill
Prepare the gas supply
1. Open the hood completely. Do not light
burners with the hood closed.
2. Make sure
control knobs are
turned to OFF.
The drip pan
must be in place
and pushed all
the way to the
back.
WARNING
Fire Hazard
Do not use grill near combustible
materials.
Do not store combustible materials
near grill.
Doing so can result in death or fire.
WARNING
Explosion Hazard
Do not store fuel tank in a garage
or indoors.
Do not store grill with fuel tank in a
garage or indoors.
Failure to follow these instructions
can result in death, explosion, or fire.
Food Poisoning Hazard
Do not let food sit for more than
one hour before or after cooking.
Doing so can result in
food poisoning or sickness.
WARNING
3. Turn the gas supply on:
• For grills using an L.P./ propane gas
cylinder:
Slowly open the cylinder valve; do not
“snap” open.
NOTE: If flow limiting device does
activate, your grill may not light. If
your grill does light, the flames will be
low and will not heat properly. Turn
cylinder valve and all control knobs
off and wait 30 seconds. After
shutting off the cylinder, very slowly
open cylinder valve and wait 5
seconds before lighting.
• For grills using gas supply source
other than L.P. gas cylinder:
Turn the shut off valve to open position
from the front of gas supply line.
3. Strike the match to light it.
4. Carefully guide the lit match between
the grill grate and one of the slots in
the sear plate.
5. Push in and turn the burner knob to
“LITE” for the burner closest to the lit
match. The burner will light immediately.
6. Repeat steps 2 through 5 for each
main burner.
7. Replace manual lighting extension
inside the drip tray.
IMPORTANT:
If burner does not light immediately, turn the
burner knob to “OFF” and wait 5 minutes
before relighting.
If any burners do not light after attempting
to manually light them, contact the
KitchenAid Assistance Center.
Lighting the grill
drip pan
Remove side burner cover. Do not light
burners with the cover on.
Lighting the side burner
IMPORTANT: Light only one burner at a
time.
1. Do not lean over burners. Push in and
turn to "LITE" the control knob for the
burner you wish to use.
2. Push in the burner ignitor button. You
will hear the “snapping” sound of the
spark. Keep the burner ignitor button
pushed in until burner lights. Make sure
burner is lit. Repeat for the other
burner as needed.
IMPORTANT:
If burner does not light immediately, turn the
burner knob to “OFF” and wait 5 minutes
before relighting.
Using the side burner
Manually lighting main grill burners
1. Remove the manual lighting extension
from inside the drip tray.
2. Attach a match to the clip.
WARNING
Burn Hazard
Do not let the burner flame extend
beyond the edge of the pan.
Doing so can result in burns.