Maintenance information and precautions – Sony DCR-TRV355E Manuel d'utilisation

Page 331

Advertising
background image

331

Additional Information Informations complémentaires

Maintenance
information and
precautions

Moisture condensation

If your camcorder is brought directly from a cold
place to a warm place, moisture may condense
inside your camcorder, on the surface of the tape,
or on the lens. In this state, the tape may stick to
the head drum and be damaged or your
camcorder may not operate correctly. If there is
moisture inside your camcorder, the beep sounds
and the % indicator flashes. When the
Z

indicator flashes at the same time, the cassette

is inserted in your camcorder. If moisture
condenses on the lens, the indicator will not
appear.

If moisture condensation has
occurred

None of the functions except cassette ejection
(

OPEN/EJECT) work while the alarm

indicator is on. Eject the cassette, turn off your
camcorder, and leave it for about one hour with
the cassette compartment open. Your camcorder
can be used again if the % indicator does not
flash.

Note on moisture condensation
Moisture may condense when you bring your
camcorder from a cold place into a warm place
(or vice versa) or when you use your camcorder
in a hot place as follows:
– You bring your camcorder from a ski slope into

a place warmed up by a heating device.

– You bring your camcorder from an air-

conditioned car or room into a hot place
outside.

– You use your camcorder after a squall or a

shower.

– You use your camcorder in a place of high

temperature or humidity.

How to prevent moisture condensation
When you bring your camcorder from a cold
place into a warm place, put your camcorder in a
plastic bag and tightly seal it. Remove the bag
when the air temperature inside the plastic bag
has reached the surrounding temperature (after
about one hour).

Précautions et
informations relatives
à l’entretien

Condensation

Si vous transportez votre caméscope directement
d’un endroit froid à un endroit chaud, de la
condensation peut se former à l’intérieur du
caméscope, sur la surface de la cassette ou sur
l’objectif. Dans ce cas, la bande pourrait coller au
tambour de tête et s’endommager ou votre
caméscope pourrait ne pas fonctionner
correctement. Si de la condensation se forme dans
votre caméscope, le bip se fait entendre et
l’indicateur % clignote. Lorsque l’indicateur
Z

clignote au même moment, une cassette se

trouve dans le caméscope. Si de la condensation se
forme sur l’objectif, l’indicateur ne s’affiche pas.

Si de la condensation s’est formée

Seule la fonction d’éjection de la cassette
(

OPEN/EJECT) fonctionne pendant que

l’indicateur d’alarme est allumé. Ejectez la
cassette, éteignez votre caméscope et laissez-le
s’acclimater à la température ambiante pendant
une heure environ en laissant le logement de
cassette ouvert. Votre caméscope peut de
nouveau être utilisé si l’indicateur % ne clignote
pas.

Remarque sur la condensation d’humidité
De la condensation peut se former lorsque vous
transportez votre caméscope d’un endroit froid à
un endroit chaud (ou vice-versa) ou lorsque vous
utilisez votre caméscope dans un endroit chaud
de la manière suivante :
– Vous amenez votre caméscope d’une piste de

ski dans une pièce chauffée.

– Vous transportez votre caméscope d’une pièce

ou d’un véhicule climatisé à un endroit très
chaud en plein air.

– Vous utilisez votre caméscope après une

bourrasque ou une averse.

– Vous utilisez votre caméscope dans un endroit

très chaud ou très humide.

Comment prévenir la formation de
condensation
Lorsque vous transportez votre caméscope d’un
endroit froid à un endroit chaud, placez le
caméscope dans un sac plastique et fermez bien
celui-ci. Sortez le caméscope du sac lorsque la
température de l’air à l’intérieur du sac a atteint
la température ambiante (au bout d’environ une
heure).

Advertising
Ce manuel est liée aux produits suivants: