Sony XM-255EX Manuel d'utilisation

Stereo power amplifier, Specifications, Troubleshooting guide

Advertising
background image

Problème

L’indicateur POWER/PROTECTOR
ne s’allume pas.

L’indicateur OVER CURRENT s’allume
en rouge.

L’indicateur OFFSET s’allume en
rouge.

L’indicateur THERMAL s’allume en
rouge.

L’alternateur émet un bruit.

Le son est étouffé.

Le son est trop faible.

Aucun son n’est audible.

Aucune tonalité de test n’est audible
lorsque la touche TEST TONE est
enfoncée.

Problem

The POWER/PROTECTOR
indicator does not light up.

The OVER CURRENT indicator lights
up in red.

The OFFSET indicator lights up in red.

The THERMAL indicator lights up in
red.

Alternator noise is heard.

The sound is muffled.

The sound is too low.

No sound is heard.

No test tone is heard when the TEST
TONE button is pressed.

Sony Corporation

2000

Printed in Korea

XM-255EX
XM-255NX

Specifications

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
55 watts per channel minimum continuous average power into 4 ohms,
both channels driven from 20 Hz to 20 kHz with no more than 0.04%
total harmonic distortion per Car Audio Ad Hoc Committee standards.

Other Specifications

Owner’s Record

The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. XM-255EX Serial No.

3-045-651-11 (1)

Stereo Power
Amplifier

Operating Instructions

Mode d’emploi

Circuit system

OTL (output transformerless) circuit
Pulse power supply

Inputs

RCA pin jacks
High level input connector

Outputs

Speaker terminals
Through out pin jacks

Speaker impedance 2 – 8

(stereo)

4 – 8

(when used as a bridging

amplifier)

Maximum outputs 120 W

×

2 (at 4

)

150 W

×

2 (at 2

)

300 W (monaural, at 4

Ω)

Rated outputs
(supply voltage at 14.4 V)

55 W

×

2 (20 Hz – 20 kHz,

0.04 % THD, at 4

)

70 W

×

2 (20 Hz – 20 kHz,

0.1 % THD, at 2

)

140 W (monaural) (20 Hz –
20 kHz, 0.1 % THD, at 4

)

Frequency response

5 Hz – 100 kHz ( dB)

Harmonic distortion

0.005 % or less
(at 1kHz, 4

)

Input level adjustment range

0.2 – 4.0 V (RCA pin jacks)
0.4 – 8.0 V (High level input)

Low-pass filter

50 – 200 Hz, –18 dB/oct

Power requirements 12 V DC car battery

(negative ground)

Power supply voltage

10.5 – 16 V

Current drain

At rated output: 15 A
Remote input: 1.4 mA

Dimensions

Approx. 237

Ч

52

Ч

170 mm

(9

3

/

8

Ч

2

1

/

8

Ч

6

3

/

4

in.) (w/h/d)

not incl. projecting parts and controls

Mass

Approx. 1.5 kg (3 lb. 5 oz.) not incl.
accessories

Supplied accessories

Mounting screws (4),
Terminal cap (1)

Optional accessories

Connecting cord for power amplifier
RC-46

Design and specifications are subject to change without
notice.

Troubleshooting Guide

The following checklist will assist in the correction of most problems which you may encounter with your unit.
Before going through the checklist below, refer to the connection and operating procedures.

Cause/Solution

The fuse is blown.

t Replace the fuse with a new one.

The ground lead is not securely connected.

t Fasten the ground lead securely to

a metal surface of the car.

The voltage going into the remote terminal is too low.
• The connected master unit is not turned on.

t Turn on the master unit.

• The system employs too many amplifiers.

t Use a relay.

Check the battery voltage (10.5 – 16 V).

Turn off the power switch. The speaker outputs are short-circuited.

t Rectify

the cause of the short-circuit.

Turn off the power switch. Make sure the speaker cord and ground lead are
securely connected.

The unit heats up abnormally.
• Use speakers with suitable impedance (2 to 8 ohms

).

• Make sure to place the unit in a well ventilated location.

The power connecting leads are installed too close to the RCA pin cords.

t Keep

the leads away from the cords.

The ground lead is not securely connected.

t Fasten the ground lead securely to

a metal surface of the car.

Negative speaker leads are touching the car chassis.

t Keep the leads away

from the car chassis.

The FILTER selector switch is set to the “LPF” position.

The LEVEL adjustment control is set to the “MIN” position.

The FILTER selector switch is settled between settings (i.e., not correctly set); set
the switch properly.

The wiring is not properly connected.

t Check the connections and re-wire

accordingly.

Guide de dépannage

La liste suivante vous permettra de remédier à la plupart des problèmes que vous pourriez rencontrer dans
le cadre de l’utilisation de votre appareil. Avant de passer en revue la liste ci-dessous, vérifiez les
procédures de raccordement et d’utilisation.

Cause/Solution

Le fusible est grillé.

t Remplacez le fusible par un neuf.

Le fil de masse n’est pas connecté correctement.

t Fixez correctement le fil de

masse à un point métallique de la voiture.

La tension entrant à la borne de télécommande est trop faible.
• L’appareil maître connecté n’est pas allumé.

t Mettez l’appareil maître sous

tension.

• Le système utilise trop d’amplificateurs.

t Utilisez un relais.

Vérifiez la tension de la batterie (10,5 – 16 V).

Coupez l’interrupteur d’alimentation. Les sorties de haut-parleur sont court-
circuitées.

t Remédiez à la cause du court-circuit.

Coupez l’interrupteur d’alimentation. Assurez-vous que le cordon de haut-
parleur et le fil de masse sont correctement branchés.

L’appareil chauffe anormalement.
• Utilisez des haut-parleurs d’une impédance appropriée (2 à 8 ohms

)

.

• Installez l’appareil dans un endroit bien aéré.

Les câbles d’alimentation sont installés trop près des câbles à broches RCA.
t Eloignez les câbles l’un de l’autre.

Le fil de masse n’est pas connecté correctement.

t Fixez correctement le fil de

masse à un point métallique de la carrosserie.

Les fils négatifs des haut-parleurs touchent la carrosserie de la voiture.
t Eloignez les fils de la carrosserie de la voiture.

Le sélecteur FILTER est mis en position “LPF”.

La commande de réglage LEVEL est mise en position “MIN”.

Le sélecteur FILTER est à cheval entre deux positions de réglage (ou n’est pas
correctement réglé) ; réglez correctement le sélecteur.
Les fils ne sont pas correctement connectés.

t Vérifiez les connexions et refaites

le câblage en conséquence.

+0

–3

Spécifications

Circuiterie

Circuit OTL (sortie sans
transformateur)
Alimentation par impulsions

Entrées

Prises à broche RCA
Connecteur d’entrée haut niveau

Sorties

Bornes de haut-parleurs
Prises à broches à sortie directe

Impédance des haut-parleurs

2 – 8

(stéréo)

4 – 8

(en cas d’utilisation comme

amplificateur en pont)

Sorties maximales 120 watts

Ч

2 (а 4

)

150 watts

Ч

2 (а 2

)

300 watts (monaural, à 4

Ω)

Sorties nominales (tension d’alimentation à 14,4 V)

55 watts

×

2 (20 Hz – 20 kHz, 0,04 %

DHT, à 4

)

70 watts

×

2 (20 Hz – 20 kHz, 0,1 %

DHT, à 2

)

140 watts (monaural) (20 Hz –
20 kHz, 0,1 % DHT, à 4

)

Réponse en fréquence

5 Hz – 100 kHz ( dB)

Distorsion harmonique

0,005 % ou inférieure
(à 1kHz, 4

)

Plage de réglage du niveau d’entrée

0,2 – 4,0 V (prises à broche RCA)
0,4 – 8,0 V (entrée haut niveau)

Filtre passe-bas

50 – 200 Hz, –18 dB/oct

Alimentation

Batterie de voiture 12 V CC
(masse négative)

Tension d’alimentation

10,5 – 16 V

Courant

à la sortie nominale: 15 A
Entrée de télécommande: 1,4 mA

Dimensions

Approx. 237

Ч

52

Ч

170 mm

(9

3

/

8

Ч

2

1

/

8

Ч

6

3

/

4

po.) (l/h/p)

à l’exclusion des parties et commandes
saillantes

Poids

Approx. 1,5 kg (3 livres 5 onces) sans
les accessoires

Accessoires fournis

Vis de montage (4),
Cache de borne (1)

Accessoires en option

Câble de raccordement pour
amplificateur de puissance RC-46

La conception et les spécifications sont sujettes à
modifications sans préavis.

+0

–3

If you have any questions or problems concerning your unit that are not covered in this manual, please
consult your nearest Sony dealer.

Si vous avez des questions ou des problèmes concernant votre appareil qui ne sont pas abordés dans ce
mode d’emploi, adressez-vous à votre distributeur Sony le plus proche.

Advertising
Ce manuel est liée aux produits suivants: