Sony XM-2751 Manuel d'utilisation

Stereo power amplifier, Xm-2751, Specifications

Advertising
background image

Specifications

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
75␣ watts per channel minimum continuous average power into 4␣ ohms,
both channels driven from 20 Hz to 20 kHz with no more than 0.04 %
total harmonic distortion per Car Audio Ad Hoc Committee standards.

Other Specifications

Features

•Maximum power output of 150 watts per

channel (at 4 ohms).

•Wide dynamic range and low distortion (less

than 0.005 %).

•Built in LPF (Low-pass filter) and low boost

circuit.

•Built in protection circuit.
•Pulse power supply* for stable and regulated

output power.

* Pulse power supply

This unit has a built-in power regulator which converts the
power supplied by the DC 12 V car battery into high speed
pulses using a semiconductor switch. These pulses are
stepped up by the built-in pulse transformer and separated
into both positive and negative power supplies before being
converted into direct current again. This is to regulate
fluctuating voltage from the car battery. This light weight
power supply system provides a highly efficient power supply
with a low impedance output.

Caractéristiques

•Puissance admissible de 150 watts par canal (à 4

ohms).

•Large plage dynamique et faible distorsion

(inférieure à 0,005 %).

•LPF (filtre passe-bas) et circuit amplificateur de

basses fréquences intégrés.

•Circuit de protection intégré.
•Alimentation par impulsions* garantissant une

puissance de sortie stable et régulière.

* Alimentation par impulsions

Le convertisseur intégré de cet appareil permet de transformer
l’alimentation en courant continu fournie par une batterie de
voiture de 12 volts en signaux ultra-rapides grâce au
commutateur à semiconducteur. Ces signaux peuvent être
démultipliés par le transformateur intégré à impulsions,
séparés en courant positif et négatif avant d’être de nouveau
convertis en courant continu afin de stabiliser la tension
variable de la batterie de voiture. Ce système d’alimentation
de faible poids fournit une alimentation très efficace avec une
sortie de basse impédance.

Sony Corporation

1996

Printed in Japan

XM-2751

Stereo Power
Amplifier

3-858-865-11 (1)

Operating Instructions

Mode d’emploi

Owner’s Record

The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.

Model No. XM-2751 Serial No.

Spécifications

Circuit system

OTL (output transformerless)
circuit
Pulse power supply

Inputs

RCA pin jacks

Outputs

Speaker terminals

Speaker impedance

2 – 8 ohms (stereo)
4 – 8 ohms (when used as a
bridging amplifier)

Maximum output at 4 ohms

150 watts per channel
400 watts (monaural)

Rated output (supply voltage at 14.4 V)

75 watts per channel (20 Hz –
20 kHz, 0.04 % THD, at 4 ohms)
100 watts per channel (20 Hz –
20 kHz, 0.1 % THD, at 2 ohms)
Monaural: 200 watts (20 Hz –
20 kHz, 0.1 % THD, at 4 ohms)

Frequency response 5 Hz – 100 kHz (

-3

dB)

Harmonic distortion 0.005 % or less

(at 1 kHz, 4 ohms, 16 watts)

Input level adjustment range

0.2 – 4 V

Low-pass filter

80 Hz, -18 dB/oct

Low boost

0 – 10 dB (40 Hz)

Power requirements 12 V DC car battery (negative

ground)

Power supply voltage10.5 – 16 V
Current drain

at rated output: 20 A
Remote input: 5 mA

Dimensions

Approx. 230

Ч

53

Ч

212 mm

(w/h/d) (9

1

/

8

Ч

2

1

/

8

Ч

8

3

/

8

in.) not

incl. projecting parts and controls

Mass

Approx. 2.1 kg (4 lb. 10 oz.) not incl.
accessories

Supplied accessories Mounting screws (4)
Optional accessories Connecting cord for power

amplifier RC-46
RCA pin cord RC-64 (2 m)
RCA pin cord RC-65 (5 m)

Design and specifications are subject to change without
notice.

Circuiterie

Circuit OTL (Sortie sans
transformateur)
Alimentation par impulsions

Entrées

Prises à broche RCA

Sorties

Bornes de haut-parleurs

Impédance des haut-parleurs

2 – 8 ohms (stéréo)
4 – 8 ohms (utilisé comme
amplificateur en pont)

Sorties maximales à 4 ohms

150 watts par canal
400 watts (monaural)

Sorties nominales (tension d'alimentation de 14,4 V)

75 watts par canal (20 Hz – 20 kHz,
0,04 % DHT, à 4 ohms)
100 watts par canal (20 Hz –
20 kHz, 0,1 % DHT, à 2 ohms)
En mono: 200 watts (20 Hz –
20 kHz, 0,1 % DHT, à 4 ohms)

Réponse en fréquence5 Hz – 100 kHz (

-3

dB)

Distorsion harmonique

0,005 % ou inférieure
(à 1 kHz, 4 ohms, 16 watts)

Plage de réglage du niveau d'entrée

0,2 – 4 V

Filtre passe-bas

80 Hz, -18 dB/oct

Amplification de basses fréquences

0 – 10 dB (40 Hz)

Alimentation

Batterie de voiture, courant continu
12 V (masse négative)

Tension d'alimentation

10,5 – 16 V

Courant

à la sortie nominale: 20 A
Entrée de télécommande: 5 mA

Dimensions hors tout Env. 230

Ч

53

Ч

212 mm (l/h/p)

(9

1

/

8

Ч

2

1

/

8

Ч

8

3

/

8

po.) saillies et

commandes non comprises

Poids

Env. 2,1 kg (4 li. 10 on.) accessoires
non compris

Accessoires fournis

Vis de montage (4)

Accessoires en option Cordon de liaison pour

amplificateur de puissance RC-46
Cordon à broche RCA RC-64 (2 m)
Cordon à broche RCA RC-65 (5 m)

La conception et les spécifications peuvent être modifiées
sans préavis.

+0

+0

Advertising