Fujioh BUF-08P Manuel d'utilisation

Installation manual, Range hood, Safety instructions

Advertising
background image

6-15/16"

44"

29-9/16"

4-

1/4"

Holes for mounting range hood

4-

9/16"

8-1/4"

9-5/16"

2-7/16"

43"

1/16"

10-13/16" 6-1/8"

31-3/4"

17-7/8"

45"

17-7/8"

16-3/4"

10-7/16"

7/8"

9/16"

14"

3-1/8"

2-3/16"

Roof cap

Duct

(For vertical discharge)

Range hood

Wood hood

Soffit

Note:
2

×7" or 1×10"~12"

round duct

Duct
(For holizontal
discharge)

Note:
2

×7" or

1

×10"~12"

round duct

Wall cap

Fan Switch
(Right)

Fan Switch

(Left)

Front Cover

Enclosure

Filter

Lamp Switch

Lamp Switch

High Switch

Medium Switch

Low Switch

OFF Switch

Pilot Lamp

Lamp (Not supplied)

(PAR20 bulb,

in the base diameter

26mm: medium base)

INSTALLATION MANUAL

Model: BUF-08P

1U03 2783

Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.

SAFETY INSTRUCTIONS

WARNING:

WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.

CAUTION:

CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.

NOTE

: The safety instructions are explained with the following

pictographic symbols.

means forcible execution. It indicates actions,
if any, that must be done.

WARNING

1. TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:

a) Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the
manufacturer.

b) Before servicing or cleaning unit, switch power

off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.

CAUTION

INSTALLATION

1. Preparation

2. Range Hood Mounting

3. Connecting Power Supply Wires

1

Remove the nut from the conduit
connector at the end of power wiring.

2

Remove one screw fixing the
wire cover then slide it to detach.

4. Final Assembly and Check

Range Hood

3. Read specification label on this product for further

information and requirements.

2. To reduce the risk of fire and to properly exhaust

air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.

6. Fasten the filter and other parts securely. Incorrect

attachment may result in personal injury or
property damage.

4. Use only for the purpose of kitchen ventilation.

1. For general ventilating use only. Do not use to

exhaust hazardous or explosive material and
vapors.

5. Do not install this range hood in the bathroom or

in other wet rooms since electrical shock and
damage may result.

2. To reduce the risk of fire or electric shock, do not

use this product with any solid-state speed control
device.

b) Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.

c) When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the

outdoors.

e) The end user is responsible to ensure compliance

with all Federal, State and Local Environmental
and Fire codes.

1

According to the conditions
where the range hood is
installed, determine whether it
will be discharged vertically or
horizontally. For vertical or
horizontal discharge, run duct
work between the hood location
and the roof cap or wall cap.
For best result in either direction,
use a minimum number of
transitions and elbows. Be sure
to attach a roof cap or wall cap
to avoid rain/wind entry.

2

The range hood unit
must be mounted to a
liner which has the
following dimensions.
Install the liner
securely after
checking that the
opening size of the
liner is the same as
the figure.

• If the range hood is not installed properly, it could become detached and

fall.

• Ensure that the metal duct does not touch other metal housing materials,

otherwise fire or electric shock could result.

• When the liner is installed in the wooden hood, the inside of the wooden

hood placed above the cooking surface must be fully covered by the metal
barrier including bottom edges. Select a suitable liner and metal barrier
according to the size and shape of the wooden hood and install properly.

• The liner should be installed tightly. If the liner installation is not correct,

the range hood unit may become detached and fall.

• Wear working gloves to avoid injury.

CAUTION:

5. Explanation to the End User

(1) Referring to the Operation Manual, explain the operation of this range

hood to end users.

(2) The Installation Manual and Operation Manual should be given to the

end user.

2

Check

(1) Turn on the electrical circuit to the range hood.

(2) Make sure that the switches and light operate correctly.

Refer to page 4 of the Operation Manual.

(3) Make sure that the range hood functions properly and it has

no abnormal noises and/or vibration.

• Electrical wiring should be done by a qualified person(s) in accordance

with all applicable codes and standards, including fire-rated construction.
An unqualified person doing the work could result in fire, electric shock
or injury.

• This range hood uses 120V AC. Do not connect to other voltage since

fire, electric shock or damage could result.

Be sure to switch power OFF
at service panel before wiring.

3

Connect the conduit through
the connecting hole of the
enclosure using the nut
previously removed.

4

Connect wires tightly and securely
using wire connectors (not supplied).
Connect the electrical wires as follows:

5

Replace the wire cover with
sliding it as shown and using
the screw removed previously.
Make sure that all wires are
connected properly and
enclosed inside of the wiring
compartment.

5

Align 4 screw holes of the liner and range hood, then fix securely
using the supplied screws (M5

×30) and nuts.

Note:

Fasten all the screws and nuts evenly.

CAUTION:

CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.

means prohibition. It indicates actions, if any,
that mustn’t be done.

4. TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

5. This unit must be grounded.

CIRCUIT DIAGRAM

6. Install this range hood to a liner. Check that the

hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.

7. Connect only to an AC120 Volt power source or

the range hood could result in fire, electric shock,
and damage.

DIMENSIONS

CAUTION:

WARNING:

WARNING:

(Unit: inch)

NAMES OF PARTS

RANGE HOOD LOCATION

1

The range hood must be installed just
above the cooktop.

2

The minimum distance from the
cooking surface to the bottom of the
range hood must be 24".

3

The total weight of the BUF-08P
range hood unit is 70.4 lbs. (32 kg)

4

Power requirements are:
AC120 V, 60 Hz, 5.8 Amp

• Check that the hood is correctly installed, since incorrect installation

could result in the detachment of the range hood and the unit could fall.

WARNING:

ACCESSORIES

Screw M5

×30

Four (4) pieces

Nut with plate
Four (4) pieces

Mounting bracket
One (1) piece

24" (Minimum)

Cook top

Liner

FWD switches & lamps side

44"

8-1/4"

4-

∅1/4"

Holes for mounting
range hood

Center line

Front

Liner Dimensions (Unit: inch)

Liner

Range hood cutout

43-3/16"

16-7/8"

Exhaust
port

Front cover

Filter
Loosen screws
to remove the filters.

Conduit
(Not supplied)

Nut
(Not supplied)

Wire cover

Hook

Lamp Switch

Fan Switch

Push to
turn ON

Turn the switch
clockwise

120V
60Hz

Connector

Connector

Connector

Connector

Connector

Connector

Connector

Connector

Motor

Motor

Red

Red

Or

ange

Or

ange

White

White

White

White

White

White

White

Blac

k

Blue

Blue

Bro

wn

Red

Or

ange

White

Blue

Bro

wn

Red

Or

ange

White

Blac

k

Blue

Bro

w

n

Red

Or

ange

White

Blue

Bro

wn

Bro

wn

Or

ange

Blue

Bro

wn

Black

White

Black

Black

Blac

k

Black

Black

Black

Black

Black

White

Black

Black

White

Green

Black

Black

Grey

Grey

Grey

Grey

Black
Black

Yellow

Yellow

Yellow

Black
Black

Pilot Lamp

Pilot Lamp

Lamp:50W

Lamp:50W

Lamp:50W

Fan Switch

Fan Switch

Capacitor

Lamp Switch

Purple

Purple

Purple

Washer

*

Bracket

*

Not supplied

Spring-washer

*

Nut

*

Mounting bracket

Beam

3

Put 4 all thread rod (

∅1/2” anchor bolt, not supplied) into the corner

holes of the mounting bracket, and secure them using washers, spring
washers, and nuts. Place the mounting bracket on the beam of the
ceiling as shown.

3. TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:

a) Installation work and electrical wiring must be

done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.

• Black to Black
• White to White
• Green to Green

WARNING:

The following method is the standard installation.
There may be some different cases depending on the structure of
the ceiling where the mounting bracket is placed or the shape and
mounting condition of the wood hood.
In such a case, please arrange best possible way according to the
condition of the place where the range hood is being installed.

Detach
the tape.

Tape

Clamper

Keyhole

Clamper

Fan unit

Keyhole

FWD

Remove first

Remove second

6

Using washers, spring washers, and double nuts, attach the range
hood to all 4 threaded rods securely.

4

Hold up the range hood,
and with inserting the
exhaust port into the duct,
pass all 4 threaded rods
through the corner holes of
the range hood.

Note:
Do not touch the switch
buttons when holding the
unit as damage may result.

Note:

The mounting bracket should be securely fastened at this point
to simplify installing the range hood later.

1

Place the range hood
as shown and detach
all filters by loosening
screws.
Then remove 6 screws
fixing the front cover
and detach the front
cover.

Note:

Pay attention not
to deform the
exhaust ports.

Note:

If taping from the outside is impossible, remove the exhaust port
and insert the duct end to the range hood directly, then make
inside taping on the duct end. Be sure to attach a duct cover with
damper in this case.

Duct

Non-flammable

tape

Range hood

Duct

Exhaust port

Washer

*

Washer

*

Enclosure

Use less than

∅1"

washer to avoid
overlapping with
the enclosure bend.

Spring-

washer

*

Nut

*

*

Not supplied

∅1"(∅25.4)

7. Keep your hands and other objects away from

the fan while it is in motion. The range hood may
injure you or damage itself.

3

Turn over the range hood and detach
the tape on the exhaust ports.

Note:

Do not remove the keyhole screws.

(3) Remove screws attaching to the top plate.
(4) Disconnect wiring connector coming from the fan unit.
(5) Slide the fan unit rightward to disengage from fixing hook,

then pull it up while avoiding keyhole’s screws to remove from
the range hood.

FWD

Connector

Slide

Slide

Remove this side unit

Hook

Screw

Screw

Connector

Push with a
screwdriver etc,
and pull off.

Liner

Liner

[Securing plate
turns while
passing through
the opening
of Liner]

Securing plate

Nut with plate

[Right & left, each two (2) places]

Nut with plate

Four screws
(M5

×30)

Slide

Slide

Hook

Screw

Attach this side unit

Bracket

Fan unit

Wire

Keyhole

FWD

(6) Three 50 Watt halogen light bulbs (not supplied)

can be mounted in this range hood.

1

Assembly

(1) Attach the fan units respectively by sliding

them leftward to engage with bracket hooks
and keyholes, then tighten screws.

Note:

Pass through the wiring over the bracket.

(5) Attach the front cover, and secure

it with 6 screws.
Then attach the filters.

Prior to function check, install
light bulbs (PAR20 bulb, with
base diameter 26 mm: medium
base), rated at 120 V - 50 Watt
or below.

Screw

Filter

Front cover

Bulb
(Not supplied)

2

Remove the fan units.

<Attention>

7

Make the duct joints secure and air-tight using non-flammable tape
such as duct tape, etc. (Not supplied)

Non-flammable tape

(2) Fix each fan unit using the

removed screws.

(3) Connect each fan unit’s

wiring connector.

Note:

Be sure to connect
firmly as illustrated.

(4) Fasten each fan unit’s

wiring clamper.

Connector

Clamper

FWD

Connector

Clamper

Note:

During installation, be careful not to
touch the fan switches. If two or more
switches are pushed at once, it may
be a cause of failure.

(1) Release each fan unit’s

wiring clamper.

(2) Remove total 4 screws

from each unit.

Fan unit

Fan unit

Remove this unit first

FWD

Fan unit

Fan unit

Attach this unit first

FWD

Check that the fan unit is hanged securely on
the keyhole screw and fixing hooks when
attaching. It may be a cause of injury if dropped.

CAUTION:

The following light bulbs are recommended for this range hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL

Turn the lamps clock-wise to install.

• To protect hands from injury, wear working gloves when installing the

range hood.

CAUTION:

CAUTION:

• The liner shape illustrated in this installation manual is only for reference.

Advertising